Jump to content
SAU Community

Recommended Posts

Hey guys run into a problem. So i didnt see my block before it went to the machine shop and got work done to it but i got it back and saw it was rb30de...so drilled and tapped to give oil and water but the tensioner as in the 2nd one on the right isnt level i think i could get away with drill and tapping it above the water pump??? Is there any threads that confirm that it works? And holds some power??

Link to comment
https://www.sau.com.au/forums/topic/456473-rb30-tensioner/
Share on other sites

Nizpro mounted both idler and tensioner above the water pump ages ago.

You'll have trouble finding what belt to use though.

And there's no such thing as rb30de block.

Its a shame you didn't check to see if the idler face was there ready to go, all later blocks had it, just early blocks didn't all have it.

Guys have made some adapters and such to get the idler mounted in the typical spot.

Link to comment
https://www.sau.com.au/forums/topic/456473-rb30-tensioner/#findComment-7530862
Share on other sites

And the belt doesn't hold power, neither does the idler or tensioner. They spin. They spin the same making 150kw ad 450kw. Spinning is spinning.

The only thing that will make a belt work harder would be stiff springs and aggressive cams, not power.

Link to comment
https://www.sau.com.au/forums/topic/456473-rb30-tensioner/#findComment-7530863
Share on other sites

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
    • -10 is plenty for running to an oil cooler. When you look at oil feeds, like power steering feeds, they're much smaller, and then just a larger hose size to move volume in less pressure. No need for -12. Even on the race cars, like Duncans, and endurance cars, most of them are all running -10 and everything works perfectly fine, temps are under control, and there's no restrictions.
    • Update: O2 sensor in my downpipe turned out to be faulty when I plugged in to the Haltech software. Was getting a "open circuit" warning. Tons of carbon buildup on it, probably from when I was running rich for a while before getting it corrected. Replaced with new unit and test drove again. The shuffle still happens, albeit far less now. I am not able to replicate it as reliably and it no longer happens at the same RPM levels as before. The only time I was able to hear it was in 5th going uphill and another time in 5th where there was no noticeable incline but applying more throttle first sped it up and then cleared it. Then once in 4th when I slightly lifted the throttle going over a bump but cleared right after. My understanding is that with the O2 sensor out, the ECU relies entirely on the MAP tune and isn't able to make its small adjustments based on the sensors reading. All in all, a big improvement, though not the silver bullet. Will try validating the actuators are set up correctly, and potentially setting up shop time to tune the boost controller on closed loop rather than the open loop it is set to now. Think if it's set up on closed loop to take the O2 reading, that should deal with these last bits. Will try to update again as I go. 
×
×
  • Create New...