Jump to content
SAU Community

Recommended Posts

Not a huge powercruise fan, sure it's fun but geez it's a lot of money to pay for big wait times to get out on the track.

Honestly better off doing an Antilag Supercruise at Collie.

http://www.thegridracing.com.au/perth/racing-simulators-perth

Who's keen?

Trev and Corey, you guys able to come up from bumfuck to participate?

Also keen to get Dale, Paul and Vin Diesel Dan out if they're all still alive.

Most likely a date in October, it's in the city so we can also get pissed have a few responsible beverages.

http://www.thegridracing.com.au/perth/racing-simulators-perth

Who's keen?

Trev and Corey, you guys able to come up from bumfuck to participate?

Also keen to get Dale, Paul and Vin Diesel Dan out if they're all still alive.

Most likely a date in October, it's in the city so we can also get pissed have a few responsible beverages.


Went there for my 30th it was shit, don't recommend it, expensive and under powered gaming pc's my personal rig is way better.
Just now, shoey85 said:

Went there for my 30th it was shit, don't recommend it, expensive and under powered gaming pc's my personal rig is way better.

Well damn.

http://www.thegridracing.com.au/perth/racing-simulators-perth

Who's keen?

Trev and Corey, you guys able to come up from bumfuck to participate?

Also keen to get Dale, Paul and Vin Diesel Dan out if they're all still alive.

Most likely a date in October, it's in the city so we can also get pissed have a few responsible beverages.



Was very keen til I saw below post.

Paulie and I keep in touch. He is way up in stoneville now so bit of a hike but I reckon he would come to a decent catch up

Some asshole in a commodore or falcon just smashed his car through the bus stop and into the wall next to my house. He sped off as quick as he could but I collected the trail of car parts he left behind.

Police report lodged. Dropping them off at the station after work tomorrow.

If it was a genuine accident I'd feel sorry for the guy, but he was just hooning/doing burnouts and speeding through a suburban Street.

This is the third time in the last four months some ones crashed there,  all for the same reason. 

  • Like 1



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...