Jump to content
SAU Community

Recommended Posts

11 hours ago, Beyond Blue R33 said:


I think my wife just worked out your plate. Is it from the old cartoon theme song. Godzilla, Godzilla and Godzookey.

I've told him this many times, but it happens to just be a coincidence that works nicely.

Don't burn the clutch out practicing

 

When you burn da clutch. [emoji52] n its lower than new.

The clutch pedal inches up or down. Other words when it bites is it lower to firewall or higher to the steering wheel when its worn. ?

 

Also is it auto adjusting or can i go do manual adjustments. ?

[emoji57]

 

 

 
When you burn da clutch. [emoji52] n its lower than new.
The clutch pedal inches up or down. Other words when it bites is it lower to firewall or higher to the steering wheel when its worn. ?
 
Also is it auto adjusting or can i go do manual adjustments. ?
[emoji57]
 
 

Being hydraulic it isn't gonna go down... I haven't burnt out enough to know this 100% but In theory the grip point will raise
  • Like 2
Ha na its from the budwiser Commercial whazzzuuuuppp but one of the guys say hey dookey pick up the phone, and i preffered z00key

How was the second day on the job Dean? Man I was tired this morning. I went and picked up a huge lump of 12mm thick pipe and some turret punchings this morning. Then done a 11hr day just got home. I know what burnt toast feels like! Scrape off the shit and start again tomorrow!
  • Like 1
13 minutes ago, Beyond Blue R33 said:


How was the second day on the job Dean? Man I was tired this morning. I went and picked up a huge lump of 12mm thick pipe and some turret punchings this morning. Then done a 11hr day just got home. I know what burnt toast feels like! Scrape off the shit and start again tomorrow!

yeah i struggled to get up big time this morning

 

what was your best pass last night? got a timeslip?

  • Like 1
Yeah not bad. How was the drive home car still good and did ya hav3le a grin going home thinking I got a 12 sec car

Panicked when I left the motor plex the diff had some judder on the first take off round the corner. Oi!. Went and done some figure of 8's and it was all good. When I changed the diff oil it did the same thing with fresh 75/90 so I got some ford l.s.d. Paste off Dave and it did the trick. I would assume from the launches and horrid rear end tramping through first and second on the slippery strip with no cornering it just pushed the good thickness out of the clutch packs. (hope so?) I launched it pretty hard close to home and it gripped and took off like a animal. I think the main problem on the launches was because I lifted the ride height on the tein basics and it firmed the whole car up on the set spring rate too much. It's pretty obvious also that the Achilles s2 are crap tyres. I scored the full set for $360 at cost price so nuff said.
  • Like 1

Being hydraulic it isn't gonna go down... I haven't burnt out enough to know this 100% but In theory the grip point will raise

I've noticed when the car is cold the full face n.p.c. Is real close to the floor. You have to bump it twice just to get going. But when the car is warm. (not thermostat hot) but driven it behaves pretty normally like the xr8.
22 minutes ago, Beyond Blue R33 said:


I've noticed when the car is cold the full face n.p.c. Is real close to the floor. You have to bump it twice just to get going. But when the car is warm. (not thermostat hot) but driven it behaves pretty normally like the xr8.

i dont think ive ever noticed a difference in any of my cars with temp...

 

maybe you have a tiny bit of air in it? no idea

yeah i struggled to get up big time this morning
 
what was your best pass last night? got a timeslip?

Best pass for the car was 12.8. But my reaction time was 0.7sec lol noob. 177kph terminal. So 13.5. I had major troubles hooking it up and had really bad tramping and wheelspin. Never done the 1/4 before. I tried dropping it at 4000.then 3500. Then 3000. And 2500 like traffic lights. Had 34psi in those shit Achilles tyres so nuff said. Lesson learned. Any tips or advice? Apart from new tyres or lower psi learned that the hard way. It only has the tein basic coil overs when I got the car it was on the deck and hooked up ok and left 11's on the road, but i raised it to 100mm all round for the police jockey wheel. through lifting it it has compressed the springs and is hard as all round. I was a bit disappointed with the times but even with a very mild launch it just tramped all the way through 1/2 under not full pedal and hooked up in 3. Bummer. Virginal. I launched it hard on the way home and it just hooked up and went with a tiny bit of tramping perfect. I thought the track would have way more grip than the street but total opposite. Live and learn. Was driving it through the the d/s window a couple of times. It has a full hicas delete but is obvious the tyres are crap with too much psi. Bummer. 4 wins and 1 loss with no Sau sticker. I got torched off the line by nearly everyone but 18psi in 3/4 sorted it. Bit embarrassing but there you have it. No traction at all. I reckon even with 100kg of sand bags in the boot would have been sweet.
3 minutes ago, Beyond Blue R33 said:


Best pass for the car was 12.8. But my reaction time was 0.7sec lol noob. 177kph terminal. So 13.5. I had major troubles hooking it up and had really bad tramping and wheelspin. Never done the 1/4 before. I tried dropping it at 4000.then 3500. Then 3000. And 2500 like traffic lights. Had 34psi in those shit Achilles tyres so nuff said. Lesson learned. Any tips or advice? Apart from new tyres or lower psi learned that the hard way. It only has the tein basic coil overs when I got the car it was on the deck and hooked up ok and left 11's on the road, but i raised it to 100mm all round for the police jockey wheel. through lifting it it has compressed the springs and is hard as all round. I was a bit disappointed with the times but even with a very mild launch it just tramped all the way through 1/2 under not full pedal and hooked up in 3. Bummer. Virginal. I launched it hard on the way home and it just hooked up and went with a tiny bit of tramping perfect. I thought the track would have way more grip than the street but total opposite. Live and learn. Was driving it through the the d/s window a couple of times. It has a full hicas delete but is obvious the tyres are crap with too much psi. Bummer. 4 wins and 1 loss with no Sau sticker. I got torched off the line by nearly everyone but 18psi in 3/4 sorted it. Bit embarrassing but there you have it. No traction at all. I reckon even with 100kg of sand bags in the boot would have been sweet.

Let the psi down, ur never gonna do much with low profile tyres anyways. Ur not gonna have much traction by just droping the clutch at what ever rpm, needs to be a gradual out with the clutch and on with the power. Like i said to pol, find that sweetspot where ur not on full boost but have some to leave with. Takes patience and practice. For the drag car we just stage it and push the transbrake button until the last amber lights up, the delay box then lets the car leaves at full noise when the light goes green lol

  • Like 1
 





Best pass for the car was 12.8. But my reaction time was 0.7sec lol noob. 177kph terminal. So 13.5. I had major troubles hooking it up and had really bad tramping and wheelspin. Never done the 1/4 before. I tried dropping it at 4000.then 3500. Then 3000. And 2500 like traffic lights. Had 34psi in those shit Achilles tyres so nuff said. Lesson learned. Any tips or advice? Apart from new tyres or lower psi learned that the hard way. It only has the tein basic coil overs when I got the car it was on the deck and hooked up ok and left 11's on the road, but i raised it to 100mm all round for the police jockey wheel. through lifting it it has compressed the springs and is hard as all round. I was a bit disappointed with the times but even with a very mild launch it just tramped all the way through 1/2 under not full pedal and hooked up in 3. Bummer. Virginal. I launched it hard on the way home and it just hooked up and went with a tiny bit of tramping perfect. I thought the track would have way more grip than the street but total opposite. Live and learn. Was driving it through the the d/s window a couple of times. It has a full hicas delete but is obvious the tyres are crap with too much psi. Bummer. 4 wins and 1 loss with no Sau sticker. I got torched off the line by nearly everyone but 18psi in 3/4 sorted it. Bit embarrassing but there you have it. No traction at all. I reckon even with 100kg of sand bags in the boot would have been sweet.

Might cable tie the wife and kids up next time and put them in the wheel well? I spun out on the lights a bit too. Nothing like the big boys on television? White amber's green. Whoops. Was trying to gradually build the boost up to 3500 about 9 p.s.i. like normal but... Whoops tramp spin ass Wednesday.
Let the psi down, ur never gonna do much with low profile tyres anyways. Ur not gonna have much traction by just droping the clutch at what ever rpm, needs to be a gradual out with the clutch and on with the power. Like i said to pol, find that sweetspot where ur not on full boost but have some to leave with. Takes patience and practice. For the drag car we just stage it and push the transbrake button until the last amber lights up, the delay box then lets the car leaves at full noise when the light goes green lol

Yeah i did it gradually even down to a traffic light take off but it just fried the tyres and tramped under 3/4 acceleration all the way through 1/2 and hooked up in 3.
Let the psi down, ur never gonna do much with low profile tyres anyways. Ur not gonna have much traction by just droping the clutch at what ever rpm, needs to be a gradual out with the clutch and on with the power. Like i said to pol, find that sweetspot where ur not on full boost but have some to leave with. Takes patience and practice. For the drag car we just stage it and push the transbrake button until the last amber lights up, the delay box then lets the car leaves at full noise when the light goes green lol

Boost night next Wednesday is going to be awesomeness when Sau shows its colours and we're all down there with our cars tools spare drag tyres, air compressors and a full range of knowledge and what not. Can't wait too learn from you guys and front up as a team so we can out perform everyone! I've booked the date in my calendar even though I'm busy at work. Can't wait!
13 hours ago, Beyond Blue R33 said:


Panicked when I left the motor plex the diff had some judder on the first take off round the corner. Oi!. Went and done some figure of 8's and it was all good. When I changed the diff oil it did the same thing with fresh 75/90 so I got some ford l.s.d. Paste off Dave and it did the trick. I would assume from the launches and horrid rear end tramping through first and second on the slippery strip with no cornering it just pushed the good thickness out of the clutch packs. (hope so?) I launched it pretty hard close to home and it gripped and took off like a animal. I think the main problem on the launches was because I lifted the ride height on the tein basics and it firmed the whole car up on the set spring rate too much. It's pretty obvious also that the Achilles s2 are crap tyres. I scored the full set for $360 at cost price so nuff said.

What diff is in it?

20 hours ago, pol1on1 said:

 

When you burn da clutch. emoji52.png n its lower than new.

The clutch pedal inches up or down. Other words when it bites is it lower to firewall or higher to the steering wheel when its worn. ?

 

Also is it auto adjusting or can i go do manual adjustments. ?

emoji57.png

 

 

Can go either way. If the clutch plate is worn we tend to have pickup real close to up top. If the pressure plate is buggered the pickup is real close to the floor.

 

They are adjustable via master cylinder to get it right




  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...