Jump to content
SAU Community

Recommended Posts


All good till the government rips the ass out of what you have earned from busting your balls. Wow look at, oh, bummer.


Yep always paying the man

I've made 10-11k a fortnight plenty of times when they offer unlimited overtime but I think from memory I only end up with 6k


I feel you on the mega overtime. have done some 26-28 hour days. Get home, pass out on the couch for a few hours and then wake up for some dinner. Far from a good time.


That's the go, getting work to pay 26-28hours for a 24hr day
  • Like 1
Any updates?



It has been quoted, assessor to review then I will have an answer, it seems like it's repairable, we have discussed our tidy up [emoji14] the 34 will be very tidy after this I'm sure [emoji6]

We have a couple of ideas that if we go ahead with will really set the car apart from others [emoji108]
  • Like 2



It has been quoted, assessor to review then I will have an answer, it seems like it's repairable, we have discussed our tidy up [emoji14] the 34 will be very tidy after this I'm sure [emoji6]

We have a couple of ideas that if we go ahead with will really set the car apart from others [emoji108]



Suicide doors and 24" mags?
  • Like 2
13 hours ago, shoey85 said:

 

 


It has been quoted, assessor to review then I will have an answer, it seems like it's repairable, we have discussed our tidy up emoji14.png the 34 will be very tidy after this I'm sure emoji6.png

We have a couple of ideas that if we go ahead with will really set the car apart from others emoji108.png

 

 

Ooooo sounds promising 

Was thinking of strengthening the front a little and running a new cai

5F021C56-AA04-40BE-AE4F-270AAE88264A-1514-0000019928DF801A.jpg.b41678dceae543f796def36451ce8707.jpg


That will make it 2 of a kind then.

Fully equipped to bash roos and do water crossings. Traction and water ingress might be an issue you want to look into though.



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...