Jump to content
SAU Community

Recommended Posts

Hi all, have had a quick search but with little to no luck.

I'm just after the diameter of the inlet and outlet of the cooler core so I can grab some more silicone joiners before I head off and grab some more tomorrow.

Cheers, Steve.

post-40313-14340055613081_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/457392-3233-gtr-intercoolers/
Share on other sites

Pretty confident it's 80mm not 3 inch, I know the engine end is 80mm. Japan don't use imperial at all afaik.

3 inch will stretch over 80mm but it's a pain in the arse. Better to just get the correct size.

Silicone will help it slip off too. I want to use Tarzan grip on mine to stop it leaking at 32+

80mm is easy enough to get these days.

Use hair spray. It wont go anywhere

Ive also stretched 3" onto the intercooler, but sounds right that it would be a typical jap 80mm (3 1/4")

Pretty confident it's 80mm not 3 inch, I know the engine end is 80mm. Japan don't use imperial at all afaik.

3 inch will stretch over 80mm but it's a pain in the arse. Better to just get the correct size.

Cos I'm picky, the Japanese do use bsp so yu r rong. Take that .

Cos I'm picky, the Japanese do use bsp so yu r rong. Take that .

Why change what works, if it wasn't for the bloody US it would probably be a world pipe standard.

Pretty sure they had laws against using imperial, as did Australia.

  • Like 1

Pretty sure they had laws against using imperial, as did Australia.

Um.....BSP is Imperial. The very definition of Imperial. It's just different Imperial to the NPT Imperial. As long as we're using "Imperial" to mean "based on units which are based on the length of some old codger's thumb".

BSP has become metricised, but the sizes are still exactly the same old inch bullshit they always were.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...