Jump to content
SAU Community

R34 Gtt Power Fc, Z32 Afm

jase-r34
 Share

Recommended Posts

jase-r34 Mentor

jase-r34

Posted
Posted

Hey guys, I have just had my car tuned and have had a Haltech ecu fitted to replace my trusty old power fc. E85 and more power awaits, so it was time to upgrade...

So the power fc comes with hand controller, and it was on my car for about 5 or 6 years. In case anyone is interested, it was tuned by godzilla motorsport while running some pretty basic mods... 3" turbo back exhaust, return flow fmic, and Greddy profec b spec 2 ebc set at around 12-13psi and made around 180rwkw from memory.

The z32 is brand new. I fitted it to the car only to remove it again as I decided to change ecu's. It also will come with a Tomei plug to suit.

Im looking for $1000 for the lot. I may sell separately, so feel free to ask.

Located sunshine coast, but will post at buyers expense.

Cheers guys.

post-44924-0-39182300-1434514806_thumb.jpg

post-44924-0-12514800-1434514848_thumb.jpg

post-44924-0-30036900-1434514884_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/457528-r34-gtt-power-fc-z32-afm/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...