Jump to content
SAU Community

Recommended Posts

so i had my car retuned a few weeks ago and the tuner noticed oil temp was consistantly high.

when it was last tuned and driven oil temp would sit at 80 degrees and now it sits between 90-100 when cruising at 100kph.

before the tune i switched from motul turbolight to penrite racing 10 10w40 and tidied up oil cooler (flipped how i installed it and moved temp sensor in line)

once the car has sat off for 10-15mins oil temp is back to 65-70.

engine:

built rb25 (2000km old, built by red r racing about 4.5 yrs ago) 6boost, gt3076 .82ex, greddy plenum, 1000cc xpurts.

nitto oil pump, rb20 oil block, mocal thermostat oil block (group buy kit), 19row setrab oil cooler (sits behind a opening in front bar), z145a filter

tuner has told me to use a thicker oil to see if that will solve the problem but i can't see how its gone from running normal to hot.

could there be another issue or changing the oil type will make that much difference?

and what oil should i try next? looking at penrite hpr10 10w50 or go back to motul?

What does your water temp do? Does your oil temp go nuts when you push the car hard? What does your oil pressure say at cruise? Always use Motul 10W 30 myself - if nothing else it can stand the heat .

Where have you moved the temp sensor from and too Rob?

The fact that youve played with the oil cooler and temp sensor makes me think either something is not right, or the temp sensor has moved from post cooler to pre-cooler

Sounds like it could be a plumbing problem. At cruise the oil shouldn't be getting hot enough to open the thermostat to send oil to the cooler. How have you got the cooler orientated in relation to the oil lines and are you sure the thermostat is plumbed correctly?

Where have you moved the temp sensor from and too Rob?

The fact that youve played with the oil cooler and temp sensor makes me think either something is not right, or the temp sensor has moved from post cooler to pre-cooler

This

Cal it's in one of the oil lines, just removed some of the adaptors I was using.Will swap it to the other line and see if there is a difference.

Oil cooler is mounted with inlet and outlet facing up. I rotated the oil block 90 degrees so fitting now faces downward and thermostat is horizontal.

Will remove the thermostat and check. Oil is getting to the cooler as it is getting hot.

Edited by robbo_rb180

If it is a temp issue (as opposed to sensor/gauge ect), picking up a bearing can result in high oil temps at low rpm/load.

Post some pic's of the oil cooler set up.

Cheers

J

Edited by XRATED

either would I, but IF he's is getting hotter than usual oil temps- just cruising...

I agree, it's more than likely a gauge/sensor re-location change that is displaying different temps.

I run the same oil (Penrite 10w40) and my oil temps sit at 70-80 when cruising and giving it stick on the road and only hits 90-100 when on the track. This is in Darwin heat too so could be more than likely gauge/sensor

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
    • Not yet quite as bad as what we've seen a Jim Berry clutch do in an R32 GTR though when it decided to cut a chassis rail in half... Still very very gnarly and a great reason to avoid.
×
×
  • Create New...