Jump to content
SAU Community

Recommended Posts

Doesn't matter they will still put the engine number onto your rego papers by doing what I said

The current rta rule is you can increase the engine capacity by 20% without needing an engineers cert as long as the engine is from the same family as the original

Doesn't matter they will still put the engine number onto your rego papers by doing what I said

The current rta rule is you can increase the engine capacity by 20% without needed and engineers very as long as the engine is from the same family as the original

If they put the rb30 engine number, will he then get defected for having an rb25det setup attached to it?

No because he requires the pollution gear from the r33 to be fitted to it, if he removes the pollution gear from the car then he can be defected for not having that but not for the bottom end being changed.

It's the same as fitting an ls3 into a car that had an ls1

  • 8 months later...

If they put the rb30 engine number, will he then get defected for having an rb25det setup attached to it?

and now to add to that, there is also a limit of 20% increase over factory power output too, see point 2 on page 3

http://www.rms.nsw.gov.au/documents/roads/safety-rules/standards/vsi-06-light-vehicle-modifications.pdf

however if someone was to have a dyno sheet with a run done at say 50% throttle you could say hey look this is proof that the motor makes less power than the standard rb25det

Pea shooter exhaust, cam gears retarded, 7psi (or a boost leak), tune with no timing

Lots of ways to reduce power for engineering.

I drilled a hole in bung I'd used to block blow off valve to create a boost leak and passed wa pits with a setup that made twice the standard power.

  • 1 month later...
yeah but the block is older than the car



Emissions controls for the Rb are all related to the head.

Mine was engineered with a high mount gt35 and 3.5" exhaust (big mufflers, no cheats to make it quiet), but mine was done years ago and I also had to go get it emissions tested. E85 and a nice big 400 cell cat or two helps make that easier.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...