Jump to content
SAU Community

Recommended Posts

Lifting base pressure 15oddpsi will see more flow for more topend

What C/R is it running

You talking about raising the fuel pressure? Its already at 58psi. Figure another 25psi when under full boost you are looking at 83psi rail pressure.

Not sure on cr

1000cc injectors is way to small for 500kw on e85.....

Or at least a Aussie 500kw that is.

This ^

I made 604hp with my -5s on my Tomei motor at 27psi (still 2.6) on E85 with 1,000cc injectors twin bosch pumps and a Walbro 460 lift pump (to surge tank) and they were almost maxed out

Most GTR-s that run -5s here in Oz make between 450-480kw max on corn syrup

I think dyno read out is a bit too optimistic IMO but we all know how to settle this don't we?

you will need a drag strip

and a go pro

and a pic of 400m..........wait..........I mean quarter mile timeslip

  • Like 3

You talking about raising the fuel pressure? Its already at 58psi. Figure another 25psi when under full boost you are looking at 83psi rail pressure.

Not sure on cr

No, I mean 58psi base is already 15odd psi higher then the base we usually see, mine is at 50psi which is already high then normal

You don't know what the compression ratio is ?

What is the smallest id of your exhaust system?

3" I believe.... And its Rickys car, just so there is no confusion.

No, I mean 58psi base is already 15odd psi higher then the base we usually see, mine is at 50psi which is already high then normal

You don't know what the compression ratio is ?

I did not build the motor so I do not know the specifics.

most modern fuel systems run 58 or so psi. That is where we normally run things. Had this car at 43.5psi in order to help with pump gas drivability but we had to turn it up. The ID1000's are rated at about 1150cc/min at 58psi.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Oh, also, forgot to add these photos I believe.
    • Thought i'd update on this. I was able to get in contact with Craig Lieberman and later on Darryl Alison (owner of Kaizo Industries). Darryl was able to help me verify that my car was in fact one of theirs and is helping me find more info on mine !
    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
×
×
  • Create New...