Jump to content
SAU Community

Recommended Posts

Hey guys, I did a compression test on my RB25det neo. What do yous think?

Dry:

Cylinder 1 - 145psi

Cylinder 2 - 147 psi

Cylinder 3 - 152 psi

Cylinder 4 - 150 psi

Cylinder 5 - 150 psi

Cylinder 6 - 154 psi

Wet:

Cylinder 1 - 182 psi

Cylinder 2 - 180 psi

Cylinder 3 - 180 psi

Cylinder 4 - 175 psi

Cylinder 5 - 185 psi

Cylinder 6 - 180 psi

Couple of months back, my car use to only blow white smoke on boost/acceleration. Then after a while it was getting a lot of knock, like 160+ on my power fc hand controller, but only while on boost. It was fine driving normal and I only boosted it every now and then to see if it'll still knock after changing some things, hoping it would have stopped knocking.... but it didn't. So I stopped driving my car altogether to prevent any further damage I could be doing.

And now when I turn my car on it constantly blows light blue smoke while idling or driving. I take my car for a little drive around my complex evey 2 weeks or so. I haven't boosted it but I'm guessing it'll be knocking and smoking even more than before.

Any thoughts? Thanks for reading.

Link to comment
https://www.sau.com.au/forums/topic/463039-thoughts-on-compression-test/
Share on other sites

The compression results seem reasonable for the age of engine. The variation isn't drastic at all. Not sure what is causing your smoking issues. I take it the fc is running the apexi maps. You shouldn't be putting it under max load when its untuned, especially since it was registering such a high knock count.

The car was tuned by previous owner at mercury motorsports. Only started smoking and getting high knock at boost mid last year. I've bought a standard rb25 turbo in good condition and will put it in when I get time. Car still drives fine when I do drive it. Just the smoke and knocking.

The car is burning oil and I'm guessing this is why it's knocking? If the turbo doesn't fix the smoke and knock, I'll probably have to pull the head out and have a look inside the engine.

Anything else I should and or shouldent be doing?

Yes. I believe you should firstly stop driving the car until you fix this oil leak and then get it to a tuner asap.

To add to my other post. Yes you are probably experiencing detonation or pinging. That's probably why your engine light is flashing on boost

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...