Jump to content
SAU Community

R33 With Haltech Idle/temp/voltage Problems

abr33

By abr33,
in Engines & Forced Induction

 Share

Recommended Posts

abr33 Proficient

abr33

Posted
Posted

Hi all, been a while since iv posted here.

In a nutshell im running a haltech e11v2 piggybacked onto the stock ecu (was to run auto) and basically something is giving noise to the ecu via the temp sensor, it can vary up to 30 degrees cycling as often as every half second or so. This causes big idle problems from shutting off to blowing smoke etc. Iv tried running both the wires separately (not both at the same time) to the ecu and the noise is still there.

Iv not been able to find anything out there with anyone having the same problem. Iv also tried a different sensor. The feed is getting 4.88V and the other is shared ground with the tps. That of which also gives me problems time to time. The noise is only there whilst engine is going and its not relative fluctuations to RPM.

Any pointers would be appreciated! cheers.

t_revz Grand Master

t_revz

Posted
Posted

Hey mate, have no idea about your exact problem but I do similar work on large mining gear.

Does the feed stay stable when unplugged and engine running? Checking across the pins and also feed to ground, are there any fluctuations. With it unplugged does the ecu show a fault or just a random number (ie -30)

Does it fault at all temps or only cold/hot?

abr33 Proficient

abr33

Posted
  • Author
Posted

Thanks for the reply,

the feed is stable with ignition but not whilst engine is running. Hot and cold doesnt matter basically the same thing. Only its worse under 70 degrees because its fluctuating cold start curcuit.

I cant disconnect it as its resistance based, if I unplug it it goes to -60 or something, which instantly kills the engine. Im going to try earth the sensor to battery but not sure if that will work.

t_revz Grand Master

t_revz

Posted
Posted

Id kick off the alternator belt next incase it's done a diode and has a slightly erratic voltage output. And double check ecu voltage for stability.

Have you done any recent welding on the car?

abr33 Proficient

abr33

Posted
  • Author
Posted

Id kick off the alternator belt next incase it's done a diode and has a slightly erratic voltage output. And double check ecu voltage for stability.

Have you done any recent welding on the car?

Probe the TPS to see if it is doing bullshit to the voltage on the common earth?

I have swapped the alternator to one with half the kms, and no welding for a long time before this began. It literally happened after being parked for 5 days.

I have run wires directly from ecu to sensor to no resolve. Im thinking of going straight from the ground on the sensor to the negative terminal on battery to rule out poor earth feed?

An GTSBoy, the tps is also brand new haha originally it was my only issue. Itd just lose the zero setting and try to idle out of the base map

abr33 Proficient

abr33

Posted
  • Author
Posted

Maybe give main chassis earths a clean too, I'd check from batt neg to sensor neg and see if it's 0v. If so I can't see it hurting earthing out the sensor to check

Yeah iv checked it all, and made a big 35 square cable for engine earth too

Does the problem change with tps disconnected? Same pulsing?

I cant unplug it or it dies lol. needs the reading to go into zero throttle idle map.

Ill have a play later in the week when I get a chance lol

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...