Jump to content
SAU Community

Recommended Posts

Hi guys,

I recently got back from holiday and saw that my carbon fiber hood on my R34 is fading and it looks really disgusting. It looks like the gel coat (or is it clear coat?) has been fading under the sun. I was wondering if anyone has experienced this before and could help me out on what products I can use to polish this out.

20160319_165002_zpsalzjzal4.jpg

20160319_164954_zpsvuz63ua4.jpg

It hasn't gone through to the actual c/b. The coat still looks thick.

20160320_103846_zpsrxukthkl.jpg

Here's a pic of the carbon fiber exposed on the end of the hood just to show how thick the coat ontop of the c/b is

I'm not sure if it's gel coated or clear coated

I would love to get it all shiny and have a reflection in it

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/463742-restoring-my-carbon-fibre-hood/
Share on other sites

You need to go visit a panel beater.

They probably won't re-clear it for you

Uh ok. I really thought I could buff this out my self with a special polish.

Would you recommend a good panel beater that does this type of stuff? And how much would they charge?

Carbon is laid up with epoxy resin. If the resin is poor quality it can oxidize and turn white like that. Try wet sanding it back with 2000 grit sand paper and polish. If the white stuff comes back to a glaze after a wet sand and polish then you're fine. If it comes up ok, I'd shoot come good quality clear paint over the top to protect it from UV.

That cracked bit looks like it needs to be reset in resin. 1:1 clear UV stable epoxy is what you want.

If you haven't used it before it can be a bit tricky. Go watch a few youtube videos and try something before attempting your bonnet fix yourself.

It probably won't get that "as new" look but hopefully that will help you out.

Carbon is laid up with epoxy resin. If the resin is poor quality it can oxidize and turn white like that. Try wet sanding it back with 2000 grit sand paper and polish. If the white stuff comes back to a glaze after a wet sand and polish then you're fine. If it comes up ok, I'd shoot come good quality clear paint over the top to protect it from UV.

That cracked bit looks like it needs to be reset in resin. 1:1 clear UV stable epoxy is what you want.

If you haven't used it before it can be a bit tricky. Go watch a few youtube videos and try something before attempting your bonnet fix yourself.

It probably won't get that "as new" look but hopefully that will help you out.

Cheers for that. This is the response I was looking for.

I did try and polish the bonnet before you posted that comment. I bought Meguiars Scratch X 2.0 for about $20 at supercheap and buffed the shit out of it.

20160320_183843_zpscvksr9q6.jpg

There is still white cloudyness underneath the surface but shit.... it looks better than before. I am going to sand it down with grit 1000 or 2000 (are you sure 2000?). Then buff it with a cutting compound and then wax. I'll see what comes out of it the next time I have time. If it fails then I'll go to plan D and put a new clear coat on

If its under the surface you need to sand back to at least that depth. Polishing wont do anything (unless you polish long enough to get down to the effected layer.)

Once you've gotten to that layer just be really careful not to go too far. Hopefully that layer is still in the clear/gel coat and you can polish it up nicely afterwards.

FWIW I'm not sure it would matter if it was gel or clear as the same polishing would be required on either (happy to be corrected here tho.)

I'd be really carful tho, I'm not sure how much longer it will last after you've done this work. Australian sun is destructive. :(

How old is the bonnet and was it from a reputable company or a Chinese knock off? (Will give you an idea of the quality of materials used)

If its under the surface you need to sand back to at least that depth. Polishing wont do anything (unless you polish long enough to get down to the effected layer.)

Once you've gotten to that layer just be really careful not to go too far. Hopefully that layer is still in the clear/gel coat and you can polish it up nicely afterwards.

FWIW I'm not sure it would matter if it was gel or clear as the same polishing would be required on either (happy to be corrected here tho.)

I'd be really carful tho, I'm not sure how much longer it will last after you've done this work. Australian sun is destructive. :(

How old is the bonnet and was it from a reputable company or a Chinese knock off? (Will give you an idea of the quality of materials used)

Ok, thanks for the advice :)

I purchased the car a month ago from someone. They didn't say where they bought the bonnet from, just got passed onto from the last seller. So I have no idea. I did manage to search a similar (or it might be this exact one) bonet online.

http://jsai.com.au/index.php/online-store-90942/nissan-r34-gtt-z-tune-style-carbon-fibre-bonnet-detail

Looks exactly like mine, so maybe it could be from here? Who knows

"Made from high quality clear resin, carbon fibre and finished in a high gloss clear gel coat."

Edited by Joni Boi

Ok here's an update on my faded bonnet. I've sanded and buffed out the white cloudy oxidation (or what ever you call it) out of the bonnet and got it to look almost brand new, so I'll leave this here for other people to see.

I wet sanded my bonnet with 1500 grit sand paper. It took ages for me to get deep enough to the damaged layer of the clear resin. So I went to bunnings and bought 800 grit sand paper and it worked much faster keeping in mind that I did not sand through to the actual carbon fiber. Only sanded it down to the shitty layer.

20160323_205753_zpsfbxdnhpr.jpg

It took me alot of hours to get it sanded down as this bonnet has alot of vents and od shapes

After wet sanding it with 800 grit I then wet sanded it with 2000 grit sand paper.

Then I let it dry and polished it with Meguiar's clear coat safe polishing compound. The next process was polishing it with Meguiar's scratch x 2.0 to get those little scratches out left behind from the sanding and buffing.

20160326_091746_zpsebufbyyn.jpg

Both of these were about $20-$30 a bottle at supercheap. I only needed 1 of each.

Here's the finished results:

20160325_115005_zpsyvmjgygt.jpg

20160326_091146_zps9ronbfvr.jpg

I was planning to spray another clear coat on after sanding but the compressor I have does not work any more. I am going to sand it again and spray on a new coat when I get a new compressor for my spray gun.

It's a temporary fix as the sun will eat through it again but I'm happy with the outcome.

Edited by Joni Boi
  • Like 4

Nice job! I highly recommend putting clear on it, even if you use some spray can clear. But don't go cheap get some decent stuff.

Also regular wax and uv sealant will help protect it as well.

I bought this from autobarn

20160326_091245_zps6upsg49t.jpg

I don't know if this is the right one, but I'll give it a try next time.

Do you know if I need to mix anything with it like thinners?

Edited by Joni Boi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...