Jump to content
SAU Community

Cefiros suspension......

RussGTR

By RussGTR,
in Four Door Family & Wagoneers

 Share

Recommended Posts

too_much_boost Mentor

too_much_boost

Posted
Posted

I'm yet to find out what sway bars fit, but i know that S13 castor rods and coilovers fit, and S13 front strut brace and R32 gtst rear strut brace.

Looks like all the rear arms are same as S13 too.

Brakes are same as S13 SR20DET brakes (ie shit). 4 pot conversion is mandatory in a barge like a cefiro

  • 2 weeks later...
Whoneedstherapy Veteran

Whoneedstherapy

Posted
Posted
They are firm they arent as bad as tein ha or he,   i can't go back they are tooo good even in my everydayer

i heard they are fairly firm, but not noticably more than any other jap brand, but that aside they are supposed to be one of the better brands over there especially if you have a little bit of track work in mind

Ceffo Proficient

Ceffo

Posted
Posted

btw guys..

Ive just had 17x8's in the front of my ceffy and they dont fit due to the fact that the tien coilovers wont makem fit as the inside of the rims rub the bottom of the coilovers. (this is a 4stud). 4x114.3 +35 offset

Remedy

1. Had to get specially made spacers (20mm) - 200 bux a pair

2. And get new studs(75mm). 48 bux for 8. (4got which code they were)

U can bang em out from behind (no pun intended) the hubs.

ceffo.

Ceffo Proficient

Ceffo

Posted
Posted
Shit with all that hassle I would have got bolt on spacers that atleast convert you to 5 stud ? (bolt on to factory 4 studs - 5 studs for the wheels)

JK

Nah its not that simple man. those bolt on spacers are very dangerous as it put more stress on your studs apparently. Unless its welded onto the hub. If u gonna be doing drifting in the thing. Who knows whats gonna happen. Ive also thought of doing it that way. but have been told otherwise

jaik Mentor

jaik

Posted
Posted

Either way, your studs go thru a piece of round metal and then into your wheels. Might be a factory rotor, might be a spacer.

Aslong as the spacers are centric (if thats the right word) and have the lip around the centre hole to sit nicely on std hub and also *into* the wheel then I dont see any issue with it.

JK

driftmeister Community Regular

driftmeister

Posted
Posted

Hi everyone,

I also had specially made spacers and they gives a shundering effect on the steering wheel. Had them for almost 3 years now after installing the 4 pots calipers (rub my rims). Using a 7x17 35offset Front and 8x17 35 offset rear. Off / On wheel balancing sometimes solve the problem only temporary. Now my handling is getting worse so I am planning of using PU bushes for the whole suspension link and those that is link to the body but not sure what brands fits, any advice?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • dyl33
      VOLK RACING GTC CENTRE CAPS

      By dyl33 · Posted

      Centre caps $250
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Duncan
      Boost cut after swap(RB25DET NEO) R34

      By Duncan · Posted

      Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...