Jump to content
SAU Community

Recommended Posts

Hi all I have a problem with my 2004 stagea that has the vq25dd engine in her. It has developed a fuel pressure problem giving the fault code P1332. My local garage who diagnosed the fault seems to think the problem is with the main high pressure pump and the nissan dealer seems to think these main pumps give hardly any problems. The car runs at low revs although very sluggish but when you put your foot down it just bogs down. Has anybody had anything similar happen.? I don't want the mechanic to replace the main pump if it could be the pump in the tank or another problem. Any help with this will be greatly appreciated

Link to comment
https://www.sau.com.au/forums/topic/464402-m35-fuel-pressure-problem/
Share on other sites

Pretty common for the high pressure pump to 'fail', but you will find it is likely just the filter inside the mechanical pump I suspect.

There are aftermarket pumps from China, not sure how good they are, but try replacing the little filter basket first.

Also there is a fuel filter around the main lift pump intank. Likely it is the original one, so it would be a good idea to replace that, and make sure you replace the tank lid Oring at the same time.

Ok. I will try that. To access the filter in the tank do you have to drop the fuel tank or can you access it from somewhere else. I gave read something about a panel under the rear seat.??

Ok. I will try that. To access the filter in the tank do you have to drop the fuel tank or can you access it from somewhere else. I gave read something about a panel under the rear seat.??

That's right; lift the seat base, and access is on the driver's side.

Thanks guys. Is the pump and filter one unit? Is it a relatively easy job to do? I'm pretty mechanically minded but is always good to know what to expect before attempting it. It's hard to find any diagrams online of whats involved

Thanks guys. Is the pump and filter one unit? Is it a relatively easy job to do? I'm pretty mechanically minded but is always good to know what to expect before attempting it. It's hard to find any diagrams online of whats involved

it is easy job. but my tips is keeping half tank fuel otherwise you may make the fuel everywhere.

pump and filter are separately but all in the fuel tank.

http://m35stagea.info/forum/viewtopic.php?f=6&t=259&sid=12889e602795fc5f158b1b452165cd82

I suspect the issue is the high pressure pump on the engine anyway, but change the low pressure intank filter first and see if it helps.

You might want to test the intank pump while you have it out, and like I said, replace the tank Oring, they aren't expensive.

Yes I saw it sitting there today when I was having a look for it. Not alot of room.The garage has quoted me $1200 to do the job. It seems a little on the high side. Hence me thinking I should put the overalls on and do it myself.Are there any tricks to getting it out easier or is it basically what you see you deal with. We took the car out today and it went fine apart from if you put your foot down.Then it just lagged. It got up to 100km/hr with no effort etc. It's only when you ask it for more it won't respond. There was a funny knocking noise under the bonnet for some months prior if it struck a hill etc. I put it down to a loose timing chain but it may of been a failing fuel pressure pump. Would that be a symptom? I will change the rear filter first I guess just to eliminate that.

I see some high pressure pumps on ebay for about $80. Over here in nz the local wrecker wants $900 for a second hand unit. What are your thoughts on this

Edited by M35 fuel pressure problem

If the high pressure pump is the issue I have a little trick to repair some of them. Probably best to PM me if the intank filter change doesn't fix anything, I can work you through a few possible solutions before replacing the pump.

Yep, sounds like DET, not something you want going on inside your engine. I suspect it's likely why the original Japanese owner ditched it at auction. We get all the screwed cars over here for that reason, I think it's very expensive to fix over there so they cut their losses.

Yes I saw it sitting there today when I was having a look for it. Not alot of room.The garage has quoted me $1200 to do the job. It seems a little on the high side. Hence me thinking I should put the overalls on and do it myself.Are there any tricks to getting it out easier or is it basically what you see you deal with. We took the car out today and it went fine apart from if you put your foot down.Then it just lagged. It got up to 100km/hr with no effort etc. It's only when you ask it for more it won't respond. There was a funny knocking noise under the bonnet for some months prior if it struck a hill etc. I put it down to a loose timing chain but it may of been a failing fuel pressure pump. Would that be a symptom? I will change the rear filter first I guess just to eliminate that.

I see some high pressure pumps on ebay for about $80. Over here in nz the local wrecker wants $900 for a second hand unit. What are your thoughts on this

Which shop quoted you $1200? If it wasn't Soichi at www.sthitec.co.nz/ have a chat to him.

Hi scotty. Replaced rear fuel filter. Rear pump ran for a couple of seconds and cut off. I'm picking this is normal if you have not connected fuel line. Perhaps sensor cutting of pump to stop it running g on a dry tank. Up for the next suggestion you had

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...