Jump to content
SAU Community

Recommended Posts

Hey there,

I was just after some parts for my R34.

Such as:-

Electronic Boost controller

3"Dump pipe and Exhuast

any other performance parts for the engine.

Intercooler

Bommex body kit-will swap or sell my current Full Nizmo Kit.

Suspension-Coil overs

Etc....

Thanx...

Link to comment
https://www.sau.com.au/forums/topic/46505-parts-for-r34-gtt-wanted/
Share on other sites

best prices for

Apexi AVCR boost controller secondhand/brand new

Greddy-

Blitz-

any brand will do...

exhaust brand doesnt really bother me...

well I can get a HKS Intercooler for $1500 include pipes

or anything better..??

Bommex body kit.. where the best place get one...preferrably Syd or melb cos im in Cbr?

Ive got the Blitz BOV super sound II- but I prefer one that make the Chutter sound.?? HKS SSQ...i think is the one..???

  • 2 months later...
  • 7 months later...

have a TD06-20G ex-R34GTT set-up, bolt-on T3 flange, with oil lines...your dump pipe may require mod to suit....also have custom plenum with R33 intake manifold runners off the above set-up,just missing fuel rail and injectors (easier to get RB25DET injectors than the NEO's) etc...

Cheers,

Michael

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...