Jump to content
SAU Community

Nismo Engine Mount Height Increase?

No Crust Racing

By No Crust Racing,
in General Maintenance

 Share

Recommended Posts

89CAL Grand Master

89CAL

Posted
Posted (edited)

Is a height increase likely to be an issue? I never noticed much of a difference with mine. I think I even held them up back to back with stock and couldnt really see a difference. If they are harder there may be a little less 'squish' with the weight of the engine but nothing crazy I would imagine.

The top of my engine is quite low because of the front facing plenum but if it helps:

14268147293_78f04134c4_h.jpg

 

 

20131205_194100_zps213145be.jpg

Edited by 89CAL
V28VX37 Veteran

V28VX37

Posted
Posted
3 hours ago, ActionDan said:

Nismo Engine Mount Height Increase?

What sort of height increase are we talking in an R34 GT-R and what other options are there that don't increase the height? 

FWIW my R34 GT-T Nismo mounts didn't seem to make any difference to where the engine is sitting.

I would have thought there might be a couple of mm difference in just the OEM mounts being squished & worn out over 15+ years...?

No Crust Racing Grand Master

No Crust Racing

Posted
  • Author
Posted

Issue would stem from what potentially happens with intake pipes as I replaced the standard suction pipes with kts suction pipes and have a jsai pod enclosure which barely clears the z tune style bonnet.

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Valve clearance for RB25det series 2

      By Duncan · Posted

      Its also worth mentioning that 30 years after it left the factory and god knows how many missed oil changes since, there is every possibility that one or more lifters are ticking because they are sticky/gummed up. To resolve that you need to pull the cams then pull each lifter, disassemble, clean, reassemble, soak in oil and re-install, and they should come up good as new.
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      What air filter are you running? Is it a panel filter in the stock air box, or a pod filter? Is the air filter the type that is oiled?   If you unplug the IACV, what rpm does the engine idle at?
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • Dose Pipe Sutututu
      Valve clearance for RB25det series 2

      By Dose Pipe Sutututu · Posted

      This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
×
×
  • Create New...