Jump to content
SAU Community

Recommended Posts

Oil going missing = air/oil separator time?

I notice that when running the engine hard its now using some oil, but there's no smoke, and i cant see any oil leaks. I would have expected to see a little blue smoke if oil was getting consumed - can the engine be burning oil if there's no smoke? Should i get a catch can/air oil separator?

To see if its getting past the rings build up some speed and then lift off for a few seconds and then accelerate - a puff of smoke at this point suggests you are burning it

  • Like 1
17 hours ago, KiwiRS4T said:

To see if its getting past the rings build up some speed and then lift off for a few seconds and then accelerate - a puff of smoke at this point suggests you are burning it

I always thought this tested worn valve stem seals, i.e, engine under vacume, then WOT and if it puffs blue smoke, valve stem seals are on way out.

On 12/14/2016 at 6:29 PM, KiwiRS4T said:

To see if its getting past the rings build up some speed and then lift off for a few seconds and then accelerate - a puff of smoke at this point suggests you are burning it

Tried it - no smoke.

A previous engine of mine used a little oil but didn't produce any smoke at all. Leak down was in the high teens. If there's no oil in the pcv system just keep it topped up. Though a catch can or air oil separator is probably a good idea on any rb.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...