Jump to content
SAU Community

R33 Gtr not getting fuel

GTRfoLyf

By GTRfoLyf,
in R Series (R30, R31, R32, R33, R34)

 Share

Recommended Posts

GTRfoLyf Explorer

GTRfoLyf

Posted
Posted

R33 Gtr not getting fuel

Hi guys, i ama new gtr owner. Imported the car frm japan about 2 yrs ago and and the car in the garage. I am finally getting it ready to get a compliance and i ran into a problem. Up untilnow the car had been starting up fine and its safe to say that the car has only been driven about 1km in these two years but i used to regularly start it up. Yesterday i went to start up the car, at first it turned on for about 4 seconds and then turned off. The car is turning over and getting a proper self but is not starting. So i checked the spark plugs and they are fine, next i checked the fuel filter and that fine too. Ihave also checked all the fuses and they are fine. Took the filter off to see if fuel was flowing when i turn the key and there was the problem. There is no fuel coming through. Then i took out the fuel pump, checked it with a car battery and it works fine. But when i put the key in i cant hear the pump prime. I think i have checked the correct relay with a multimeter and that is working aswell. It was next to the battery, have added the photo of the relay. Can you guys tell me what could it be? Any help is appereciated guys.

image.jpg

image.jpeg

Link to comment
https://www.sau.com.au/forums/topic/468269-r33-gtr-not-getting-fuel/
Share on other sites
Shoota_77 Veteran

Shoota_77

Posted
Posted

That is the correct relay. Check to see if you have constant 12v at pin 3, if yes have you got power going in to pin 1 while cranking and coming out of pin 5 while cranking. 

If yes to all of the above then there is a problem between the relay and the pump. Check the connector going through the fuel pump hat to make sure not burnt out or no corrosion causing poor connection.

if its not that then move further down to between the hat and the pump. 

Hopefully that helps!

89CAL Grand Master

89CAL

Posted
Posted

What were you checking?
The relay will need power and earth for the coil to switch the relay which then should put power on the NO contact in the relay.

So you should have constant 12v at the power in (pin 3) of the switched side, 12v on one of the coil side terminals (prob pin 1) when the key is turned on (remember that with the engine not running the fuel pump will stop after a few seconds, should be able to remove the CAS and spin it by hand to make the fuel pump come back on) and there should be ground at the other pin on the coil side (pin 2)

Pin 5 and the power into the fuel pump should have a good circuit, I would expect less than 1ohm of resistance

GTRfoLyf Explorer

GTRfoLyf

Posted
  • Author
Posted

I hooked up the multimeter to the relay terminals. I am getting a constant 12v in no3 and 12v in no1 when i turn the key. Only getting about 0.4v in no5 when i crank. Also checked the brown grounding wire that goes to the grey and brown plugs on top of the fuel pump. Spliced the wire and grounded it directly to the battery, still nothing. Both the fuel pump connectors (brown and grey appear to be in good condition with no corrosion.

Shoota_77 Veteran

Shoota_77

Posted
Posted

Put blade connectors onto wires then put straight 12v/ground onto the terminals in the top hat. If it runs look at the fuel pump relay again if it doesn't, you'll definitely know that the problem is in the tank.

Also grab a relay from under the bonnet and switch with fuel pump relay to cancel that out. The relays are all the same. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      $5 Clock upgrade for R32 GTR

      By GTSBoy · Posted

      The attached document is fine. I just downloaded & opened it.
    • ToothDR32
      $5 Clock upgrade for R32 GTR

      By ToothDR32 · Posted

      Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
×
×
  • Create New...