Jump to content
SAU Community

Rb26 heater hoses

Giaccovitch
 Share

Recommended Posts

Sinista32 Grand Master

Sinista32

Posted
Posted

Depends what you asked for

http://www.kudosmotorsports.com/catalog/water-pass-heater-hose-piece-nissan-skyline-p-1653.html

From the Kudos website for the R32 GTR. $312 for the genuine Nissan 10 hose kit

 

But if your OCD like me - there is also air hoses (2 or 3) and the radiator hoses upper and lower ($150). and for good measure at a great price is the metal water tube (under plenum) for $40 and water tube on the upper timing case.

 

Giaccovitch Enthusiast

Giaccovitch

Posted
  • Author
Posted
2 minutes ago, Sinista32 said:

Depends what you asked for

http://www.kudosmotorsports.com/catalog/water-pass-heater-hose-piece-nissan-skyline-p-1653.html

From the Kudos website for the R32 GTR. $312 for the genuine Nissan 10 hose kit

 

But if your OCD like me - there is also air hoses (2 or 3) and the radiator hoses upper and lower ($150). and for good measure at a great price is the metal water tube (under plenum) for $40 and water tube on the upper timing case.

 

I reckon it would be worth changing all of my hoses as the car has been sitting in the weather non running for 10 years, I will show you what kudos quoted me

2380_2017-03-27.pdf

Sinista32 Grand Master

Sinista32

Posted
Posted (edited)

That's good, a good price. Probably remove the SAMCO upper and lower radiator hose set for $128 as your quote already has the OEM set in it.

Grab the metal under plenum tube for $38 and water tube on the upper timing case. Tendency also to either rust or leak.

You have all the blow bye hoses included too.

So yeah, a very good price. :thumbsup:

Edited by Sinista32
Giaccovitch Enthusiast

Giaccovitch

Posted
  • Author
Posted
Just now, Sinista32 said:

That's good, a good price. Probably remove the SAMCO upper and lower radiator hose set for $128 as your quote already has the OEM set in it.

You have all the blow bye hoses included too. So yeah, a very good price.

Cheers buddy, appreciate it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The king 2.0
      Nissan fuga 450gt android screen

      By The king 2.0 · Posted

      Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • MBS206
      NC MX5

      By MBS206 · Posted

      My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • dbm7
      Automatic Power Button Light Flashing

      By dbm7 · Posted

      Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Duncan
      R34 Plug Identification

      By Duncan · Posted

      Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...