Jump to content
SAU Community

Recommended Posts

Can't found whats wrong with my RB

Hi !

First of all, sorry for my bad English, i'm French.

Try to explain the more accurate.

 

Car is 1993 R32 GTS-T on stock RB20DET.

Just have decat, catback and HKS Air filter.

BUT, i can't check inside the ECU (Left door stuck closed)

 

The problem:

Engine cut and go randomly but more to more often.

Its happen really more when car is hot but doing sometime when cold.

I can more run good when cold, and start problem after ~10kms

 

Sounds like all the ignition is off, and on, and off...
Like OK for 4 sec and 1 sec off, etc..  etc..

Sometime back good for 30 sec and start going wrong again.

Really random :/ 

If i run on really low demand on the car, i can up to 110km/h for ~15kms before the problem

 

I try an other CAS, same thing.

 

Don't know if its relative to this problem but:

I have the first coil dead last week.

I replace (By an old one) it and go back on 6.

Today, the first coil is again dead.

 

 

Hope you have idea of whats wrong :/

PS: I just order the Nissan Consult cable, maybe it help me to check TPS Sensor or other things.

 

Sounds like theses problems:

http://zilvia.net/f/showthread.php?t=469254

http://www.gtr.co.uk/forum/149846-ignition-spark-keeps-briefly-cutting-out-pls-hlp.html

 

Edited by 1337Htune
Link to comment
https://www.sau.com.au/forums/topic/470355-cant-found-whats-wrong-with-my-rb/
Share on other sites

Les coupures apparaissent aussi quand tu reste sous les 2000 rpm ?

C'est bien des coupures franches et pas des ratés d'allumage ?

Ca arrive que quand tu charge ou même en roulant a vitesse stabilisée ?

 

J'ai eu un problème de prise de soudure des fils de MAF sur la mienne après avoir installé le maf de Z32. Exactement comme toi, OK à froid et dès que ça chauffait un peu ça coupait/revenait. Si je restait sous les 2000 aucune coupure. Mais AFR à 10.

Regarde ta prise de maf et si le faisceau n'est pas abimé.

 

Le problème de la 1ère bobine qui crame 2 fois coup sur coup par contre j'ai jamais eu. Après t'as ramplacé une vieille bobines par une autre vieille bobine. Peut-être une simple coincidence que la seconde crame comme la première.

 

Tu as quoi comme bougies actuellement, gappées à combien, et combien elles ont de bornes.

La caisse est stock et en bon état ou elle à été bricolée de partout ? Particulièrement le faisceau, il est dans quel état ?

Pas d'alarme de posée ou un truc dans le genre ? Turbo timer ?

T'es d'ou exactement ?

 

Better translation :

Hi all, I need help to sort a problem on my RB20DET. The engine is pretty much stock : no cat, aftermarket catback and HKS air filter.

The engine is cutting out randomly while driving. It happens more and more frequently especially when the engine is hot. It can drive fine when cold but after 10km or so the cutting begins. If i drive smoothly and at low load I can reach 110 km/h for about 15 km before the problem appears.

 

Things that has already been done :

An other CAS has been tried but no change.

The coilpack on cyl n°1 died last week. I replaced it with an other used one and it died again today.

 

I can't have access to the ECU, the left door is shut closed so I can't remove the panel that protect the ECU.

/ Better translation.

 

I asked if it was really the engine cutting or if it was some misfires, it's description lead toward really to engine cutting rather than misfires. I also asked which sparks plugs it has, the gap, how many km they have, if it has an alarm or a turbo timer that could have been badly wired, the shape of the engine wiring.

I also told him to check the MAF plug and wire to sse if there is no damage that could explain the cuts when running above 2000rpm.

Quote

 

Je vais essayer de rien oublier:

Oui ca me l'a deja fait sous les 2000rpm

Oui coupure totale, pas des raté.
Stabilisé ou en charge ca change rien.

J'ai quand même la sensation que si je cherche a tirer dessus, ca coupe moins. Mais pas sur au point de prendre ca comme paramètre pour la panne.

 

Bougies stock, NGK Neuves. Ca me le faisait avant et apres avoir changer les bougies.

Oui stock globalement.

Il y avais des mano greddy cablé n'importe comment sur le poste pour les alims mais j'ai tout retiré, aucun changement.

Pas d'alarme

 

Je suis du 09 au sud de Toulouse

 

Yes i have the problem under 2k rpm too.

All goes off, not misfire.

On boost or not, no change.

 

Stock brand new NGK, got the problem before and after change them.

Car have greddy gauge badly wired on the radio but remove them.

No Alarm

Si ça le fait aussi sous les 2000 c'est plus génant, le MAF ou son faisceau ne serait pas en cause du coup.

Je sèche un peu, mis à part un problème de 12v qui se coupe genre le relais d'alim de l'ECU qui coupe l'ECU, le faisceau qui va au CAS abimé...

Un pote à eu un truc dans le genre dans sa sunny swappée CA18DET mais c'était le connecteur du faisceau qui va sur l'ECU qui était pas assez serré, la caisse coupait de temps en temps totalement, tu filait un coup de latte au niveau de l'ECU et ça repartait, des fois avec un retour de flammes de la mort mais ça repartait. Toi ça coupe et ça reviens comme si de rien était j'ai l'impression.

Commence par vérifier les cables/la prise au niveau du CAS.

Tu as David qui possède DGmotorsport dans ton coin, ou Jérôme qui y bossait avant et qui est à WG british racing maintenant qui pourrait jeter un oeil.

It's going to be heat sensitive electronics.  Coil packs, ignitor, CAS, AFM are the leading items in the engine bay that will do it.  The other thing is simply the loom plugs for all these things.  They can get old and brittle, with oxidation on the contacts.  Get them warm and things move or the resistance changes and they stop working.

The other leading possibility is the fuel pump.  Could be running OK to start with but dying off as it warms up.

Any decent mechanic should be able to help fault find this stuff.  You may need some parts for swaptronics though.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi There I went through a rabbit hole of reading about Xenon headlights and the ADR regulations for having them installed. As people have been defected by running factory xenon I was researching in ways to make them compliant. Everyone always say needs to be self leveling and have washer installed, which I don't necessarily agree with. For this argument I'm using R34 as reference as I'm more aware on the construction of the headlight compared to the R33 Xenon, which may still be the exact same case.   For the self leveling clause taken from ADR 13 - Installation of Lighting and Light Signalling Devices on other than L-Group Vehicles As you can see the bold text "these manually adjustable devices from driver seats" are fine to use. As Series 1 Xenon model headlights do have a 4 level adjuster on the right near the ignition (however not series 2) then these model are consider compliant in that argument.   For the Self Cleaning aspect of this argument clause taken from ADR 13 - Installation of Lighting and Light Signalling Devices on other than L-Group Vehicles Now i can understand the argument that Xenon will need a washer as they are over 2000 lumens, but I clicked on the 12 at the end of that sentence and it takes me to the end notes which states R34 for headlight lenses are plastic, not sure if PL is mark as I don't currently have my skyline to confirm that marking is there. But could you not technically get a lenses with the PL marking on it and then get away with the argument that you need a washer. I went through a quick read of the adr and might have missed something else that may cause them to be non-complaint.    But wouldn't these technically be complaint headlights   Would love to hear other people input on this and shed some light   Edit In regard to the the washer portion I might be mistaken ADR 45 (which I believe is Regulation NO.45) states 12 cd (candela) I dont understand that portion in regarding to calculating the candela if anyone can shed some light. Otherwise I guess throw in a washer for the headlight and you definitely comply.
    • Took it to all Japan day, flogged the hell out of it and took it all, am a very very happy man  don’t know how that ended up in Greg’s thread before
    • Hey Nismo, any chance in the world you still have these seats?
    • I'd say closer to OG GTX3582R, just smaller trim - so 59mm inducer/82mm exducer as opposed to 62/82 for the first gen GTX3582R. Yeah EFRs were boss, the EFR8474 is still an absolute beast and it perplexes me that people still go to things like Turbosmart/Garrett etc when the results people are getting with those are pretty unremarkable compared to what you could get with a turbo available well before those options came out.  DriftSquid (I think) "upgraded" from an EFR9174 to a Turbosmart turbo and promised a comparison video - and kinda shuffled awkwardly and did a bit of diversion from the fact that they didn't get any improvement going to the currently massively hyped brand of turbo from a turbo that was a bit of a frankenstein that had been well superceded in it's own range before the Turbosmart unit he put on there even came out. I suspect the EFR would outperform most Xonas for what a lot of less-insane RB owners would go for, in the 400-600kw range but the Xonas are looking hard to beat up to maybe in the mid 700kw range at this stage- basically where EFRs don't really reach, and before the Precision turbos take over.  What the Xonas do well in the "EFR range" is be easier to package etc, and work very well if a divided housing doesn't suit your application.  
    • Are you sure the gasket is blown? What are the issues? Thermocure is the only flush I've seen do anything with rust, very impressed with that, Prestone, rust will be by the pool having a cigarette.  
×
×
  • Create New...