Jump to content
SAU Community

Recommended Posts

ATTKD brake kit

Anyone run the ATTKD brake kit from Just Jap ? If so, what are these like and what setup did you go with ?

Would there be much difference in going 8 pot with small pistons are just go with the 6 big pistons ?

Are replacement pads and rotors easy to come by and what sort of price ?

http://justjap.com/brakes/brake-kits/attkd/nissan/attkd-brake-kit-nissan-skyline-r33-93-98.html

thanks

Link to comment
https://www.sau.com.au/forums/topic/470639-closed-attkd-brake-kit/
Share on other sites

ATTKD, D2, G4 etc are said to all come from the same factory, Many of us run them and they work well. Being two piece rotors you just need to replace the rings, and JustJap sell them. The pads are the same size as some AP calipers, so there's a big pad selection. 6 vs 8 pot is not going to make a noticeable difference. Try searching on those other two brand names and you'll find plenty of info.

  • Like 1
44 minutes ago, MrStabby said:

ATTKD, D2, G4 etc are said to all come from the same factory, Many of us run them and they work well. Being two piece rotors you just need to replace the rings, and JustJap sell them. The pads are the same size as some AP calipers, so there's a big pad selection. 6 vs 8 pot is not going to make a noticeable difference. Try searching on those other two brand names and you'll find plenty of info.

 

MrStabby - do they still make G4 brake kits anymore ? Alot of posts I have found are 11+yrs old on them....

Would the new ATTKD be similar to these 11yr old G4 in terms of brake technology or would the new ATTKD be much better ?

I bought D2 brakes some years ago. Disc brakes have been around for about 115 years and they have not seen huge improvements in technology in recent history.

D2 type brakes are way ahead of those found in most modern cars (other than expensive super cars).

  • Like 1
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...