Jump to content
SAU Community

Recommended Posts

But remember the more you raise the rail pressure and ram more fuel throught the injector you change the spray pattern

And you have to leave some headroom in the fuel pump for boost. :headspin:

Around 45psi rail pressure.  its a trade off.  aftermarket inj. cost tons, raising the rail pressure costs F A.  If u had the coin to need 65psi rail pressure u would change the inj anyway.

And since most fuel pumps are rated at 73.5 psi, you would only have 8 psi left for boost. That's not much :wassup:

How long will your fuel pump last if you fit a FPR - ie compared to if you didn't fit a FPR ??

A) The same as if you didn't fit the FPR ?

B) Less because you are labouring the Fuel Pump ??

c) More because of some unknown reason ??

I suspect (B)

And since most fuel pumps are rated at 73.5 psi, you would only have 8 psi left for boost.  That's not much :wassup:

To get that sort of power I assumed you would already be on boost. Surely an aftermarket rising rate regulator will allow you to maintain a slightly elevated fuel rail pressure and then rise it to 65psi by the time you are on full boost.

I don’t have a problem with using a RRR, but if you are pushing that type of power (and I am assuming you have replaced the turbo, fuel pump, computer, intercooler) then surely the cost of injectors is worthwhile even if it’s just insurance for your motor.

How come I get 92-94% injector duty quite regularly with 0.85 bar and standard turbo?

 

One day it hit 100% when i wasn't looking but it seems to have these microsecond spikes like 65% when you've barely touched it.

Car is running rich?

To get that sort of power I assumed you would already be on boost. Surely an aftermarket rising rate regulator will allow you to maintain a slightly elevated fuel rail pressure and then rise it to 65psi by the time you are on full boost.

Yep, that means full boost is 8.5 psi. :rolleyes:

Car is running rich?
You should see my fuel bills! Jeez man. Weird thing is, at the track the exhaust goes brown like it's running lean.

I'm thinking of putting a 2nd hand SAFC in there till I can afford an emanage and a good tune. The ECU I have makes it run so smooth but I think it's just putting way too much fuel in.

Magic1s GTS has 435rwhp on stock injectors and uprated pump,this is the most we have seen sofar on stockers and we have never had any problems at high fuel pressures.

We will fit a bigger pump and see how we go.

This power is in shootout mode.

I see around 80% duty cycle from my 550cc injectors with no FPR and Bosch 044 pump with around 312kw@wheels.

I see around 80% duty cycle from my 550cc injectors with no FPR and Bosch 044 pump with around 312kw@wheels.

That's about right, I have seen around 565 to 570 cc's out of injectors rated at 550 cc's.

So 570 X 80% / 1.34 - 60 = ~300 rwkw

Your 312 rwkw is a pretty good effort. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...