Jump to content
SAU Community

Recommended Posts

Stock camshafts on built motor

This isnt for an RB engine, but I thought it might help others who could be curious or for future reference.

Does anyone have an experience with built motors running OEM-spec cams?

My SR20 has had a lot of porting work done, plus Ti retainers/upgraded valve springs, aftermarket exhaust manifold, bigger turbo etc. Has been running big cams in the past and I'm really curious to see how much more "driveable" and how much low-down can be improved by going back to stock cams.

I am looking for some ideas or feedback before I commit money to OEM cams + installation + re-tune.

For reference: current cams are 272 duration, 11/12mm lift. OEM are supposedly 248 duration, 10mm lift.

Link to comment
https://www.sau.com.au/forums/topic/471142-stock-camshafts-on-built-motor/
Share on other sites

Bit of a loaded question without disclosing turbo size/spec and static CR, and even fuel type + ignition mapping "down low".  All those things will play a part.

Without committing too much $$ you could try a dyno session and adjust the current cam phasing to see if it will build better torque at lower rpm.

Otherwise on topic, there's plenty of SR (and RB) owners running more basic engine upgrades with just a turbo change and OEM cams who are very happy and don't need to rev the tits off them to get satisfactory performance. Turbo spec will have a massive impact on how the engine performs over its whole rpm range.

 

0.86

The engine specs have been through 3 different tuners, one leaned it out pretty heavy at 2500rpm and it was better but still not nice. Cams were dialled in by engine builders as per spec sheet provided.
Not sure on timing.

Tuners and engine builders are not always operating on the same plane.  Or even a high plane.  And it's no good if they don't understand what you're trying to achieve when recommending specs.  So lots of opportunity to miss the mark.

Making an engine run lean where you're trying to make it "come on" is counter productive IMO.  And ignition timing is very important, so if you can, you should look at the ignition map and learn.  There's a lot of easy to access net resources, try hp tuners for a look.

Suggest a change to 0.6 turbine housing will help with the mid range boost response, at the expense of some top end revs

If you're running a 4wd Bluebird or Pulsar (guessing from earlier post?) you probably want (ie definitely need) bulk mid range anyway.

272 cams are too big for an SR on a gtx28... as in, many many sizes too big. If this was a drag car or you wanted to win WTAC, and you had a GT35 to spool up then it's a different story.

On the other hand, with your setup OEM cams are too extreme in the other direction. Given the GTX2867 with (as Dale pointed out) quite a large turbine housing for a 2L, which entails spooling up a bit later anyway.

Unless you're revving much higher than standard, 256 (poncams etc) are likely the best option, especially if you want to retain better driveability for street duties. If you're concerned about power, check out this build log - 264s were switched out for 256 duration poncams to get a better powerband. The end result was still 351kW on a GTX3071r  http://www.trak-life.com/trak180-redemption/

bear in mind that this is an unregistered track car, so streetability wouldn't have been a concern in any way.

 

Edited by Skepticism
On 08/07/2017 at 0:13 PM, Dale FZ1 said:

Suggest a change to 0.6 turbine housing will help with the mid range boost response, at the expense of some top end revs

If you're running a 4wd Bluebird or Pulsar (guessing from earlier post?) you probably want (ie definitely need) bulk mid range anyway.

 

1 hour ago, Skepticism said:

On the other hand, with your setup OEM cams are too extreme in the other direction. Given the GTX2867 with (as Dale pointed out) quite a large turbine housing for a 2L, which entails spooling up a bit later anyway.

Unless you're revving much higher than standard, 256 (poncams etc) are likely the best option, especially if you want to retain better driveability for street duties. If you're concerned about power, check out this build log - 264s were switched out for 256 duration poncams to get a better powerband. The end result was still 351kW on a GTX3071r  http://www.trak-life.com/trak180-redemption/

bear in mind that this is an unregistered track car, so streetability wouldn't have been a concern in any way.

 

I appreciate the input guys, but I think you're misunderstanding my question and why I'm asking.

I'm not chasing better turbo response, or to reduce lag. This is simply sub-3000rpm driveability and lower idle is what I'm trying to improve. I dont care about peak power, and I'm aware smaller cams will shift the power band. I'm looking for input running OEM cams on a built valve train.

The GTiR head is mechanical/solid (not lash/hydraulic like regular SR heads) so camshaft choices are generally aggressive. The car was previously running Tomei 260 Procams and it wasn't any friendlier to drive. This is a track-focused car, but I do drive it on the street. And you're right Dale, I should speak to my tuner about  the setup and potential improvements.

It will be fine. You have lower ramp rates and a lower overall lift so the only effect it will have on the valve train is a positive one. The upside to OEM cams is they are generally ground to a very high standard unlike a lot of aftermarket cams and therefore are likely to not chew up your rocker arms. It's worth checking your spray bars while its apart as SR's have a tendency to clog up.

270 is a big cam on a low comp engine, remember that you are lowering your dynamic comp with large cams that have a longer period of overlap and relying on positive pressure in the manifold to generate any real efficiency. Furthermore the effects of camshaft duration are magnified on smaller displacement engines.

You will end up with higher cylinder pressures and peak torque will shift, so your tune will need to be adjusted. 

  • Like 1
37 minutes ago, Leroy Peterson said:

I'm not chasing better turbo response, or to reduce lag. This is simply sub-3000rpm driveability and lower idle is what I'm trying to improve. I dont care about peak power, and I'm aware smaller cams will shift the power band. I'm looking for input running OEM cams on a built valve train.

Understood.

By way of a recent experience that may help: We've shaken down the Emo after a prolonged upgrade/build period.  I appreciate that a 4G63 - SR20 comparison is not apples-apples, but it is a 4wd platform that counts for heaps.

No porting, but lightweight retainers, upgraded springs, and (against my advice) some Jap cams advertised specs around 270.  Actual cam doctor measurements showed significant variance from advertised, and staggered/unequal between inlet - exhaust.

Turbo choice budget Kinugawa TDO6SL2-20G split pulse 10.5cm.

Result on 24psi bleeding to 22psi by 7000rpm was 380awhp, monster mid range torque from 4000rpm.  Idles good and smooth at 900rpm. Doughy sub 3000rpm. We have assessed that OEM cams would probably have brought the useable torque floor down 500rpm, and manipulating boost control probably seen no loss at higher rpm.

Car was second quickest in its category (behind a modified R35 GTR) even though we were just shaking it down.  So it had "enough", and we aren't focused on hp numbers either, just a quick/reliable track car.

SR with big duration cams really requires revs, and those things have a deserved reputation for spitting lash pads when using the revs.  Talk to the people doing your work, but I agree with komdotcom, OEM cams will only make the cam train work with much less stress for probably as good a result. 

  • Like 1

I think people should look at all the valve timing evens which means more than just cam lift and valve seat to seat duration . Quite a few aftermarket cams are compromised so that they drop in with few or no modifications . Obviously priority no 1 is not killing the standard valve train .

I'll see if I can link the Tomei USA page where you can look at all the numbers ie lobe center lines and overlap timing for their cams . 

https://www.tomeiusa.com/cam_spec/cam_spec_list-e.html

I've never looked at aftermarket SR20 cams but if they are anything like RB25 Poncams they'll have a lot more overlap than the factory standard cams .

Cheers A . 

Edited by discopotato03

Yeah, i know advertised cam specs are to be used as a guide only. Most cam manufacturers specify if springs and retainers are recommended with the cam, so i dont think the top shelf camshafts compromise performance for the sake of stock valvetrain.

With the GTiR head being lash type rockers, tomei poncams are not compatible, only Procams can be used. And with most GTiR builds being wannabe GTRs with 600hp good for about 2 launches, mot available cams are aggressive. I did find a mild cam but it was even less duration and lift than OEM!

If you want to have an informed conversation about a good cam package for your car and its specific use(s), I suggest that you go and see Clive at Clive Cams in Ferntree Gully. 

There are quite a few decent grinds from smaller players (not big jap tuning companies) for the SR which are quite good, a mate has one of the old Super Tourer grinds in his IPRA 1600 and it's fairly decent at low RPM for a 306 duration (advertised) cam.

I still reckon you are better off with stock cams though, you turbo isn't big enough to make it worthwhile. I'd much rather have a punchy 230kw car than a laggy 270kw car.

I've been to Clive cams before for replicating a grind and their machines were limited to 10mm lift I think.
But yeah, I will speak to tuner and then hunt down a set of OEM cams. If I'm not happy with the outcome, I'll probably revert back.
Thanks for contributions.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...