Jump to content
SAU Community

Recommended Posts

Hmmm, reading into them tonight, might not be what I'm chasing.......

Luckily I was pulling them back off either way.
Still have the 7s to use.
But, I was hoping for a little more.

Why not just keep the 7s and see what they make on e85, then race it like that to work out all the problems and if the cars not doing the times you want then you can look at something else.

Just get it running right before you worry about making 450kw

-9's won't get anywhere near 450 mate.
-7/-9 are close enough to each other they're not worth discussing the differences really.

Original goal was 400.
That would be terrific for track work I reckon.
40 minutes ago, luke gtr said:


Original goal was 400.
That would be terrific for track work I reckon.

JEM reckon my car will make 350ish when i go back to E85, after i fix a couple of issues (that i told you about the other day Luke)

Realistically if you want 400 -9's will struggle as well...you'll either need -5's or a nice single. considering a precision turbo is cheaper than -5's id just do that, get someone to fab you a manifold. 

In saying that i'm weighing up my options for my next turbo, because im a stubborn flamin mongrel and a but of a "purist" ill be sticking with 2 turbos....

If the motor is healthy you should be able to push around 350kw on E85 with the -7's. Spend the extra cash on the diffs, and enjoy. 

350-400KW, Quaife front Diff, modified transfer case, nismo rear diff=ultimate street car IMO

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...