Jump to content
SAU Community

Recommended Posts

3 hours ago, ActionDan said:

In that last glory pic, is there a pool of oil under it lol

Also are you tiny or is the driver f**king massive?

Yep, big milkshake under it. 

Anthony is a big bloke, driver seat is hard up against the roll hoop. 

  • 3 weeks later...

Well spent a bit of time this week going over the 180sx in preparation for hill climb tomorrow. Compression test came back 115-120 across all 4, the blow by had filled half the compressor housing and Intercooler with oil so pulled it apart gave it all a good clean.

Dropped the oil and there was no shiney bits so fresh 20-60 oil went in with a new filter. Still blew a little bit of smoke on quick test drive so see how it goes tomorrow and may give it a bit more boost. 

Hopefully holds together for a few runs. 

1 hour ago, ActionDan said:

Cold and dry? 

warm. 


Ended up 5th outright with a 1.01:89 at the hill climb but only did 3 runs as blow by got worse. Thats a new pb too so will be alot quicker with a healthy motor
It was blowing oil up the boost solenoid ref line and out the port.
Tried venting catch can to atmosphere which helped a little bit but still pushing oil to catch can. On the last run turned it up to 22psi but blew off intercooler pipe on gear shift after launch so called it a day.
Pulling engine this week as couldn't find another one locally.

1 hour ago, ActionDan said:

The only way a vent will help is if you vent the sump and the head separately like I did on mine. 

You need to equalise the pressure top and bottom. 

 

Will be doing whole new catch can/breather setup when I get this motor freshened up. Atp 2l can and all dash 10 lines.

Priced up everything for forged bottom end through golebeys so once engine is out and everything measured up will place the order. 

IMG_20200927_181348.thumb.jpg.71b2bbf3ae40c52f506c4b29e9b3960b.jpg

34 minutes ago, ActionDan said:

Even with a fresh motor, Nissans need bulk breathing capability. 

Vent it top and bottom and happy days.

 

2x - 10 off the top, 1x - 10off the sump and the factory block fitting should be hopefully help. Never had issues with the s14 but the rocker cover is a better design. 

  • 2 weeks later...

Progress back moving under its own power. 

IMG_20201007_174738.thumb.jpg.83b25b9d2e9893a5c0c125ff7fe7f499.jpg

Been spending a little bit of time sorting out the power steering setup since I didn't end up going electric. Went with an aeroflow tank as I stuffed up the original one trying to weld on dash fittings. 

Cut off the old bracket and made a template, copy to aluminium, cut/drilled and folded. 

IMG_20200928_194210.thumb.jpg.69f65f3fdbc3797944de04bbb1bff9af.jpg

IMG_20200930_153657.thumb.jpg.f66e93551ad59addad0f9f5077750ba9.jpg

Finished making lines and filled with fluid only to find I had hoses the wrong way on the rack. Switched them around, Bled it up and everything thing was all good. 

Also fixed cooling set up by moving one of the fans, got a new nismo thermostat just incase as the old one was around 11 years old. New coolant with demineralised water and now temps around 80c at idle. 

IMG_20201007_084614.thumb.jpg.e1ffd3ddb4ed7c594531e95a326f870d.jpg

Still sorting idle with ethrottle as when I stab the throttle it doesn't return to idle smoothly or stalls so will keep adjusting the proportion and stall gain to make it right. List of things needed to get back on the road is getting smaller. 

  • Like 2
11 minutes ago, robbo_rb180 said:

sorting idle with ethrottle as when I stab the throttle it doesn't return to idle smoothly or stalls so will

That won’t be helped by adjusting the throttle pid settings, it will be your base throttle table referenced before closed loop takes over. 

  • Like 1
7 minutes ago, Ben C34 said:

That won’t be helped by adjusting the throttle pid settings, it will be your base throttle table referenced before closed loop takes over. 

Thanks for the info will have a look at that before I do anything else. 

Just spent a bit of time this morning doing a few small things like fitting indicators, rear speaks, shortening intake pipe and cooling plates. 

IMG_20201009_112451.thumb.jpg.4f5c5a6eaf7678d6c0a152e5ee911a47.jpg

IMG_20201009_114057.thumb.jpg.b9ece166766690ee0add7ef8c6632a7c.jpg

IMG_20201009_114413.thumb.jpg.003b932f31e2f56cdb412189ddfd5f83.jpg

Engine bay all done just need to fit a washer bottle in the corner 

IMG_20201009_122206.thumb.jpg.59fd6f3388b42fe214373688c030cea6.jpg

Thanks to @Ben C34 advice went back and checked the ethrottle setup and set it up properly so idle is smooth at 800rpm and doesn't stall ?

Big ticket items left is driver side lca, cat back exhaust and Coilovers. 

 

  • Like 1
1 hour ago, iruvyouskyrine said:

how much were the brand new indicators

 

Cheaper than r33 xenon lights ?

 

Were around $500 ? 

Almost looks like it came from factory with all the "standard" Nissan parts. 

IMG_20201011_131909.thumb.jpg.abdf121abd323d20e8d3eff173a3505b.jpg

  • Like 4

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...