Jump to content
SAU Community

Recommended Posts

Hey fellas

i got an issue that just arised last week and it's driving me crazy !

car will cold start and idle fine, hot idle is fine but when I'm driving if I down shift and the rpm is over 2000rpm and then pop in neutral it will stay idling at 2000rpm

sometimes it might fall back down to 1000rpm after 5seconds or so but most of the time it will stay there until I pump the throttle then it will settle to 1000

if the car is idling and I pump the throttle again it will idle at 2000rpm until I give the throttle a quick jab the it will settle

 

im running a hypertune plenum and 90mm throttle body, gave the throttle body a clean afew days ago and did a tps reset still no change

also did a pressure test and seemed good

I noticed driveability issues around the 2000rpm like it surges too

i spoke to hypertune and they said to send them the throttle body to test (incase shaft seals are leaking, it's only 2 years old) and to rebuild if necessary 

 

if anyone has any other ideas I can try that would be great

 

thanks

 

 

 

 

 

 

Edited by SiR_RB

What are your plastic throttle spring retainers like? I had a similar issue and it turned out being the plastic retainers had perished and the springs were binding

edit: scratch that I've just read you are running a single throttle.

Edited by Sub Boy32
Was a Muppet and didn't read the OP

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...