Jump to content
SAU Community

Recommended Posts

Hi guys,

Been out of the scene for some time but i am finally in the market to purchase a gtr. I am currently looking at one that has surface rust all underneath, however,  on the strut tops and in the boot-well are completely clean.

As the car came out of factory with the cold weather package i am a little weary that there is rust places with limited access without removing panels or jamming a camera between panels etc. I am just wondering if anyone can recommend a panel shop that knows skylines quite well and can go over the car for me before purchasing around the Blacktown area.

Also just wanted to see what everyone's thoughts are of the rust underneath and strut tops. It seems to me that the strut tops look all original but i am a little iffy as the sealant on the seams is quite thick in places compared to the gtst that i had a few years back.

 

1459391598897.jpg

1459391600476.jpg

1459391625282.jpg

1459391627051.jpg

1459391628766.jpg

1459391630285.jpg

1459391632063.jpg

1459391633761.jpg

1459391635915.jpg

1459391637620.jpg

1459391639211.jpg

1459391640827.jpg

1459391642400.jpg

1459391644129.jpg

IMG_0056.JPG

IMG_0067.JPG

IMG_0069.JPG

IMG_0070.JPG

20171223_193148.jpg

Link to comment
https://www.sau.com.au/forums/topic/472967-panel-beats-familiar-with-gtrs/
Share on other sites

Seam sealant around strut tops doesn't look original mate. 

If a BCNR33 hasn't come into the country early e.g. 2000's, chances are the jap rust will work its way through those seams on the strut tops. Go look at the GTR CO UK forums and there are plenty of owners pulling engines out and replacing strut towers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...