Jump to content
SAU Community

Recommended Posts

I’ve recently picked up a 33 GTR front bar as part of the ongoing collection of parts for the GTST>GTR conversion I’m stupidly doing - but I want to get the lip back to raw plastic, no paint, without damaging the plastic underneath.

 

There’s a few things I’ve seen around - Aircraft Paint Remover (US only it seems), some graffiti remover (So Safe yellow label), but I’m not sure if there’s a better way to be doing this. Some of the paint is already spiderwebbed from impact I believe, so hopefully that helps?

 

Open to suggestions. I know I could just paint it black, but it wouldn’t be the same.

 

IMG_7571.jpg

Link to comment
https://www.sau.com.au/forums/topic/473253-paint-removal/
Share on other sites

I did the same on an R32 GTR front lip, used the paint stripper in a big spray can from Repco and a long handled dish scrubbing brush to agitate it then use a pressure washer to rinse it all off. Took maybe 3-4 goes until it was all off, but there was a couple of layers of paint on there.

The plastic didn't seem to mind, just make sure you wash it well and remember to wear gloves and a mask of some sorts.

Link to comment
https://www.sau.com.au/forums/topic/473253-paint-removal/#findComment-7866710
Share on other sites

Many years ago when i use to paint cars we would just use normal paint stripper.

The trick is to give a quick scratch up with some 80 or 120 grit, dont use any force as you only want to scratch the surface.

After this apply it with a brush in a lighter coat, dont pool it on excessively and done like there were never any issues.

Only time we used a different stripper was for some rubber moulds that were painted but it was stupidly expensive and didnt work great.

Link to comment
https://www.sau.com.au/forums/topic/473253-paint-removal/#findComment-7866799
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...