Jump to content
SAU Community

Recommended Posts

The motor is an Rb25de from an R34. I noticed my tps voltage was .20 closed. I adjusted it to oem specs at 4.5 or so and that's when I started getting the high adle around 1300-1500. If I unplug the aac the idle goes back to normal. If I set any values on the aac in consult the idle goes back to normal. I thought I may have a bad tps and installed a new unit but the same thing. The aac adjustment screw is all the way down (and broken so I cant back it out again). I've cleaned it out a while back but never had an issue until now. Not sure why my idle is screwed now because I touched the tps..

Edited by ~KnuckleDuster~
Link to comment
https://www.sau.com.au/forums/topic/474489-high-idle-after-tps-adjustment-r34/
Share on other sites

Anyone? If I'm a dummy feel free to let me know. Iv'e attempted to set the base idle per the write ups, I lowered the tps closed voltage back to where it was at .2 and still high. Cleared the ecu memory. Not sure if there's another song and dance I need to perform to have the new tps setting dialed in or if the next step would be to open up the aac and inspect that.

The R34 also has a manual throttle stop bolt, I always found that adjusting that was easier than the screw in the side of the AAC itself which appears to be made out of something with the strength of warm butter.

I had many R34 AAC's fail in general to the point where I bypassed it with a BMW unit lol

The timing was around 17* last I checked when the idle was low enough. The throttle stop bolt is backed out all the way.

The black plastic adjustment screw which was broken off was at least tightened all the way down which is the lowest point for the idle to be at but the idle was still at 1300. I chipped out the broken screw and put in a medal adjustment screw from an rb26. Now the idle is at 2k. If I unplug the aac the idle is still high around 1100-1200. I just don't get why adjusting the tps from .2 to .4 has f'ed this whole thing up!

Worst part is I'm in the US and finding an AAC from a DE is insanely difficult.

 

 

Edited by ~KnuckleDuster~

How sure are you that you don't have a leak? What happens if you block off the hose going to the IACV?


In the end I hollowed out my R34 IACV entirely, and just ran another IACV in the hose that runs to it. Only going to really work if you have an aftermarket ECU that is controlling said IACV though.

Note: My 34 one failed and when it fails, it fails open. As above, no leaks, throttle stop bolt entirely out, idle of 2000RPM.

Why not just change TPS voltage when closed back to 0.2? I noticed in my car (again not completely the same) that voltage when car on but not running may have been 0.2, but I would find that 0% throttle with car running the voltage was different, perhaps 0.5 actually.
 

Pretty sure I don't have a leak, I have a full time vac gauge in the car. Ill see what happens when I block the hose off and run it today.

If I could get away with just bypassing this thing I will. I'll do that as a last resort. I put the tps back to 0.2 and the idle was still 1500. Used to idle around 750-850 prior to me touching the tps.

I'm using the consult port and running datascan software so I can select values on the aac. If I put it anywhere from 1-9 the idle drops down. So it's as if the aac is just staying wide open unless manually told to do something different.

Edited by ~KnuckleDuster~

Ok so blocked off the vac to the aac and started it up. Still revs to 2k but will hunt from 1300 to 2k. With the vac blocked and aac unplugged the car starts up fine and the idle is wavering around 1000, revs and sounds healthy.

Is that a sufficient enough way to bypass this thing? Is it ok to leave the coolant running through it?

Edited by ~KnuckleDuster~

The coolant should be left going through it as it is the high point bleeder on the whole circuit.

"Bypassing" is by just blocking off its air supply is a bit crude.  You own't have idle up for air-con or high electrical load.  But if it's already idling high, that's probably not going to stall you out.

I would try another ECU.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That still isn't a lot to go on. I don't have a Y50 Fuga Head Unit wiring diagram. I can say that a lot of nissans of that age shared head unit plugs, so if you are in Australia something like this would probably help: https://aerpro.com/app091# You plug that into the car loom, then either plug the head unit ISO into that (if it has ISO), or you buy and ISO adapter harness that you wire in. Bit of stuffing around, but once you have ISO its easy to change things in future.
    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
×
×
  • Create New...