Jump to content
SAU Community

Recommended Posts

Missing under load, white smoke, stops missing when warmer, still residual smoke! This started about 100klms after a dynotune.

I don't really want to fork out another $1200 until I have a rough idea what the problem may be. Any ideas?

Car has a Haltech Platinum Pro ECU and a single Garrett 3076R turbo.

Tardo

Link to comment
https://www.sau.com.au/forums/topic/474872-gtr-r-32-smoke-after-dyno/
Share on other sites

Hey guys, amazing what a bit of investigating can do. Found a corroded and leaking coolant pipe under the intake manifold, which probably explains the white vapour/smoke. The missing under load was caused by a cracked spark plug on number 4 cylinder. I thought a head gasket issue was unlikely cos they're pretty bullet proof on the 32, so glad I didn't rip into it!

Tardo

  • 2 weeks later...
On 9/13/2018 at 8:16 AM, Tardo said:

Hey guys, amazing what a bit of investigating can do. Found a corroded and leaking coolant pipe under the intake manifold, which probably explains the white vapour/smoke. The missing under load was caused by a cracked spark plug on number 4 cylinder. I thought a head gasket issue was unlikely cos they're pretty bullet proof on the 32, so glad I didn't rip into it!

Tardo

Good result. If you are replacing pipes under the intake manifold, do them all in one go. Kudos Motorsport sell a kit. I even ordered OEM hard lines and replaced them while at it and the parts that plug into the block. And to add, knowing corrosion has started on that side in the coolant pipes, the turbo side will only be a few months away from doing the same so if you are going motor out I'd go to braided lines on that side too. 

Also where do I find one of these bullet proof head gaskets?.. haha.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
×
×
  • Create New...