Jump to content
SAU Community

Recommended Posts

Hi. All. Not sure im posting in correct area. Ive recently purchased a v35 stagea v6turbo. Wagon. Which I love, and hoping to do some future go fast mod too.

Issue is it dies in the backside as soon as put under load ?, i.e ..as soon as it starts to spool, she acts like she's just sucking air..? And ckokes..? 

And if i attempt to force it, it just chokes further, and / backfires. 

Ive replaced fuel filter, and take also looks clean. And replaced air filter. 

While there is slight improvement,  the problem is still there. 

Im a newbie to the v6turbo, and to the site. Im based in Adelaide? 

Any advice at this stage would be appreciated.  Thanks in advance! :)

I can point you to a good mechanic on Adelaide's north side if you need.  Diagnosing this sort of crap across the internet is usually more frustrating than helpful and it almost always turns out to be something other than what was suggested by the helpers.  Your problem could be caused by dead coilpacks, dying fuel pump, crappy AFM, a massive vacuum leak, dirty injectors, or something as simple as badly set timing.

  • Like 1
6 hours ago, M I K E said:

Check all of your intercooler piping for leaks first - something you can do yourself and won't cost anything 

8 hours ago, GTSBoy said:

I can point you to a good mechanic on Adelaide's north side if you need.  Diagnosing this sort of crap across the internet is usually more frustrating than helpful and it almost always turns out to be something other than what was suggested by the helpers.  Your problem could be caused by dead coilpacks, dying fuel pump, crappy AFM, a massive vacuum leak, dirty injectors, or something as simple as badly set timing

 

6 hours ago, M I K E said:

Check all of your intercooler piping for leaks first - something you can do yourself and won't cost anything 

Thanks both of you. I will do that.

A good mechanic is invaluable.  If you have a number / Mike. That be great. 

Cheers. Appreciated. :):)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...