Jump to content
SAU Community

Recommended Posts

Hello,

So I bought a relatively stock R34 GTR and after 500kms (all was working fine) the engine just shutdown on the highway.

The engine is cranking but refuse to start again.

 

So in the correct order, I checked using the supplement service manual:

-no engine light at any moment

-fuel pump (I can hear it when I switch on the key and the fuel pipe gets hard)

-checked all the fuses next to the throttle pedal and also in the engine bay

-self diagnostic give me error 55 (so no malfunction)

-I have 12V to the coil ignition on the power pin of this coil

-I don't have an oscilloscope however when cranking the engine I must see like 0.06V to 0.09V on the command of the coil ignition using a multimeter but I got 0v on each command of the spark plug

-wiring of the ignition coil is okay (continuity test)

-There was an aftermarket ignition control box (adic siccle advanced ignition control) connected to the ECM; so I removed it however after doing so I got error 20 ? (the orignal hairness seems to be intact !)

-I open the ECM but didn't find anything bad (bad soldering, blow components ...)

 

So this investigation supposed that the ECM is not working properly ?!

 

Question :

-what is error code 20 ?

-if the ECM is working fine; what are the causes that avoid it to command the ignition coils ?

 

There is also an aftermarket alarm I normally desarm it (using the key fob) code alarm PF7600 I don't think there is a relation to my problem but I mention this.

 

Thanks for any hint

Link to comment
https://www.sau.com.au/forums/topic/477754-r34-gtr-no-sparks/
Share on other sites

There is no ECU code 20 for GTRs, unless they've added some secret sauce to the R34 that wasn't in the earlier ones. (although 21 is the ignition circuit.....you sure you got 20 and not 21?)

A multimeter cannot be substituted for an oscilloscope unless you're looking for a steady voltage. They are not fast enough to see brief signals.

I would say the ADIC is responsible. You'd best base your research around it.

 

Edited by GTSBoy

My GTR was build in 08/1999

Well I'm sure it's 20; two long blink followed by a pause of like 5 seconds and then again 2 long blink.

Yes I know for the multimeter but that's only what I've got for the moment...but I should see at least some variation on the voltage which is not the case; I measured 0V continuously. I will borrow a scope and try again.

 

I don't get any information on the ADIC :/

Like I said before removing it I got 55 and after removing it I got 20

 

Can you elaborate choyda ?

 

Thanks for the help I really appreciated it

Edited by bigboss59400

CAS is the thing on the end of the camshaft that tells the ecu when to fire the plugs and injectors. If you are going to take it off and haven't got a timing light mark it carefully so you that if its ok you can put it back in exactly the same position. Turn it by hand to feel if the bearings are stuffed. With the key on turn it and see if it fires the plugs (maybe pull one out and look for a spark (making sure it has a good earth). If it does look inside the cas and the end of the cam shaft to see if the drive has been damaged.

21 minutes ago, GTSBoy said:

Yes, because there are no codes ending in zero.....

I didn't noticed that thanks!

22 minutes ago, GTSBoy said:

And ref the root cause - probably ground the drive off the end of the cam, by the looks of all them chips in there. 

Okay I will remove sensor and see

On 7/15/2019 at 3:20 AM, bigboss59400 said:

Just for information I found some on aliexpress

They look OEM I will buy and see

Thanks for all

There are basically two - one with plastic cap like yours Hitachi 2371 5L 300

The other one is a Mitsubishi with metal cap 2371 02U11 which will not work.

Have a look at the end of the camshaft and see if the drive appears to be damaged.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Kinda glad I never got to this ..    https://www.facebook.com/groups/1483859159195077
    • @GTSBoy This method was able to get readings of -10 to -2, so it looks like its monitoring.  Now I need to figure out why the vacuum on the line provided isn't alternating with manifold pressure.  I went with 2 lines that an RB25 tuner recommended but I'll get a longer hose and try directly off the back of the manifold.  He may have been used to OEM intake setups while I have a DBW setup that removed the MAF and IACV.  
    • I work at a car detailing and tinting shop called Quark which gets all manner of German cars in usually (mainly due to a contract with Mercedes Benz Kita Osaka, BMW Nishinomiya and others) but every once in a while something special comes in, like a fully restored 1972 HS30 Nissan Fairlady 240ZG... The shop owner had immediately started applying film to the windows as soon as it was in the shop so the interior was completely covered in towels and plastic sheets. But I could get a few photos of the engine bay which was restored like new. Such an amazing car to see in pristine condition in Japan these days.  
    • Was going to say the car pulls up nicely everywhere, especially going into that last long right hander before the main straight. Looks like a lot of fun.
    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
×
×
  • Create New...