Jump to content
SAU Community

Recommended Posts

Hello All,

So I've gone through the scratching window saga and the replacement part is obsolete so I've used a boating carpet off cut suggested to me on this very forum.

My next problem is the top window rubber sills - they have gone hard and all 4 have warped in areas.

Does anyone have a model number or even better a hack to replace with something that will be easily available and cheapest?!

Thanks in advance. 

Edited by LINK17
Spelling

Better put up a photo & point out what you're talking about. Seals on the body that the top of the door glass seals against? Seals on the top edge of the door (inner & outer) that the glass slides up between? 2dr or 4dr.

Edited by GTSBoy

Ok it's actually not as bad as I thought. All of the rubbers are hard but not brittle and not on all doors. Pics attached. Maybe some hot water, stretch them out then condition them?

Apologies for some of the pics, bad time of day but all of the outside sills are good. Its just a few have warped on the inside?

20191022_173536.jpg

20191022_173542.jpg

20191022_173549.jpg

20191022_173628.jpg

20191022_173635.jpg

20191022_173650.jpg

20191022_173701.jpg

20191022_173707.jpg

20191022_173758.jpg

20191022_173805.jpg

I have bought inners and outer of those for a 2dr recently. They're available, but not cheap. Not horrifying expensive yet either. But....4 dr? Who knows? Your best bet will probably be to enquire at Amayama and jp-carparts.com to see what's available.

You won't massage them back to life, is my bet.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...