Jump to content
SAU Community

Recommended Posts

Hey guys, my first post on here. So long story short I own an R33 Skyline Series 1 RB25DE auto from 1993, and its completely stock. I went down to the shops and the car was driving fine, started fine etc.. but when leaving the shops, I did what I normally do by putting the key in the ignition, turning it to the "ON" part, clicking the immobiliser button in, and the dash lights/ radio all lit up as usual for a second or two, and just before i turned the key to start the engine the dash lights/ radio lights just shut off. I had my mechanic whos a family friend come out to look at it, as I suspected it was maybe a flat battery, but we were getting 12.57V to the battery in the boot, we tried to jump start but to no avail. Something else that was odd was to the terminals in the engine bay where you can jump start from also, we were getting no voltage reading, but he said it may have been because the terminals were so dirty. He seemed to think it could be a fuse issue or immobilser but he didn't have the tools to help/ didnt wanna mess with the immobilser or fuses. My cars stranded at the local shops for 48hrs until I can claim service from RAC as I only just signed up for it tonight. Has anyone had a similar issue or maybe could point me in the right direction as to what is wrong with it? Also theres a little red light that will flash 24/7 next to the ignition and when the key first gets put in (without turning at all) theres a beeping sound which I suspect is the alarm, but even that red light wont flash at all. I hope this isn't the end of the road for my car :( any help would be greatly appreciated, thanks guys

Edited by Kyle1234

Didnt make it completely clear, but in short the dash lights wouldn't turn on at all. No crank either when turning key which usually would mean flat battery also. Theres a little green light on the immobilser that will light up when pressing it, and that is lighting up fine, so I guess its not a dead battery in my immobilser? 

18 minutes ago, Kyle1234 said:

Theres a little green light on the immobilser that will light up when pressing it, and that is lighting up fine, so I guess its not a dead battery in my immobilser? 

Doesn't take much power to light that little lcd mate, my remote stopped operating the immobilizer, but was still lighting up. Batteries are cheap. Also check your earth lead.

Edited by Rusty Nuts

Auto-elec will work out what is wrong with it in about 5 minutes. It will be the ignition switch failed, or something equally dull. Or maybe the shitty immobiliser thing hiding in there. In which case your auto-eleccy will curse your name as he pulls it out because they hate them because they do this sort of shit.

You should just pay for a tow to get it out of the carpark and into a workshop.

47 minutes ago, trel said:

Another thing before calling an auto elec just pull out fuses one by one if you can't find the English translated panel on the net and look for a busted fuse,  replace with same rating as necessary. 

With your alarm system, did you remove that yourself? I found an image on google that as this but im not sure what category the alarm fuse would be under. I might just wait till RAC can help tomorrow night, and if they cant then get an auto elec to come look at it, i would have a go myself but i just dont wanna fk it up moreImage result for r33 fuse box english

You're not looking for the fuse that feeds the alarm. You're looking for ANY fuse that might be blown and hence interfering with the car starting.

Any decent alarm installer should never take power from a fused source in the fusebox. They should take power direct from a hot feed and the alarm should have its own fuse.

4 hours ago, GTSBoy said:

You're not looking for the fuse that feeds the alarm. You're looking for ANY fuse that might be blown and hence interfering with the car starting.

Any decent alarm installer should never take power from a fused source in the fusebox. They should take power direct from a hot feed and the alarm should have its own fuse.

Yeah as gts said. Stick your head under the steering column you should see some wires with fuses on them, most likely for the alarm, check them out. Other than that I can't help anymore.

I got a mobile auto elec to take it out for me car was completely dead. Should cost no more than $200 for a mobile guy to remove it. I paid  $185 for an hour plus his callout. Anymore than that and they're ripping you a new one.

Hey guys, so after getting the rac to jump start the car and get it back tomy house it was still dead, turns out the metal under the bolts where the earth lead comes up to the battery had been painted over, which caused issues, and my earth cable is actually too small and being strangled a bit so gotta replace that. These older rac guys are so knowledgable its crazy, the young bloke who got my car out of the shops just said it was a dead battery but batterys actually fine in the end. Thanks so much to everyone that replied in this thread it helped me a lot to try and diagnose the issue, and get a better understanding! Legends!!

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...