Jump to content
SAU Community

Recommended Posts

Hello all. I have a 93 skyline gtst. Gas leaks from the left of the white nipple that you see in the picture. It goes from full tank and leaves me with a quarter tank and does this within a matter of hours.  When it leaks its a small steady stream until my tank is down to a quarter. I plan on putting the car on a ramp this weekend but wanted opinions on where it may be coming from? A leaky hose,  seal? I'm mechanically inclined but is this an easy job or should I leave it to a garage to fix? Any help is appreciated. Thank you!

20200213_091110.jpg

Link to comment
https://www.sau.com.au/forums/topic/479760-leaking-gas/
Share on other sites

When my tank leaked it only leaked until about 3/4 tank. Turns out an evaporation hose on top of the tank, a breather hose attached to the filler hose, and the fuel pump o-ring had all gone bad. Replaced them all and it has been perfect. Not sure how different a GTS tank is from a GTR. If your tank is leaking all the way down to 1/4 tank then it's probably a hole somewhere down low, you might be able to see it without dropping the tank. 

Dropping the tank itself isn't too hard to do in your garage if you have a buddy and can be done in an afternoon. There's a post on here that gives pretty good directions with pics. Of course a garage with a fuel tank lift would be able to do it much faster. At least since so much is leaking out you don't have to worry about draining/siphoning out (as much) fuel first, but keep in mind that even at 1/4 tank, gas is heavy. 

Link to comment
https://www.sau.com.au/forums/topic/479760-leaking-gas/#findComment-7924786
Share on other sites

Update: well it seems that it is leaking from the weld seams. it wasn't from rusting out but just came apart from a bad hit. Ive tried to look for gas tanks specific to that model but should I expand my search to other models? If so,  anyone know what other tank will fit in there? I can have the shop weld the seams back together. If I get it welded, will it hold better or just the same shit?

Link to comment
https://www.sau.com.au/forums/topic/479760-leaking-gas/#findComment-7924848
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
×
×
  • Create New...