Jump to content
SAU Community

Recommended Posts

I have just acquired the M35 250RSTurbo and have a post up elsewhere but thought this topic needed it's own identity .

I have read up about the 3200 CFM fan and the failures of going to electric  thermo fans .

It seems to me that if you consistently require that kind of cfm then perhaps the radiator is a bit undersized .

We all know that after about 40 Kph there is more air coming in than the fan can pull so we want the fan to stop otherwise it impedes the incoming air blah blah blah .

I am very unhappy with the roar and would have gone to good quality thermo's but having read up about do not need to follow suit .

However being the same as the V35 chassis I decided to check out the later 3.5 engined [ is that a word ?? ]  V35 and they have thermo fans but still the tiny single row radiator .

Was that a cost cutting exercise to have a viscous...Yuk !!

Anyhow the intent was to get a V35 radiator with fans knowing that the radiator will bolt in to M35 but the fan shroud might not bolt to the M35 radiator .

Whew , did you get that , was dam hard to write .

So couldn't get a radiator but do have the shroud with the twin fans , will be checking if it swaps in later today .

I'm not noble enough to believe I might be the only one to think of this or maybe I am ??

Has this been done ?

Was it successful ??

I think a twin row radiator will help as well and seeing that the tanks fail will go an all alloy radiator in the future , what is everybody else running .

Thoughts please including if you think I'm a raving lunatic !!

Edited by M35.Groot
Link to comment
https://www.sau.com.au/forums/topic/480452-m35-viscous-fan-mods/
Share on other sites

4 hours ago, M35.Groot said:

Was that a cost cutting exercise to have a viscous...Yuk !!

No. Wrong statement.

If you have a lot of fan noise, then the problem is the viscous clutch is stuffed and all you need to do is replace it with a GENUINE NISSAN clutch. Do not f**k about with aftermarket off brand clutches, because they all suck compared to the genuine Nissan one.

I know about these things.

 

I'm sure you do know about these things  however if you read the post carefully you will note I'm going to use genuine NISSAN fans from a NISSAN V35 and shroud not some random aftermarket fans .

Also I wish to eliminate the 6Hp odd loss that a viscous fan sucks away .

My car is still running the stock pithy radiator and I'm aware they fail so will fit an all alloy twin core radiator to avoid that which can't hurt .

 

Where is your evidence that the stock radiators fail more than any other...and will your all alloy twin core radiator exactly fit the V35 shroud?

How does the  fan suck 6hp away? It is only operating at idle or in traffic. At normal speed the clutch is disengaged .

Presumably your twin electric fans work the same way. From whence comes the power to drive them if not from the engine?

With the km your car has done you should probably be saving up for a new turbo or timing chain (after you have replaced your fan if it is faulty).

Wow !!

Don't want to upset anyone , chill the whiskey factory guys ? .

First the radiator thing , I'm not saying it fails more than any other , however in the last two nights I have read at least 8 posts from different people that their radiator plastic tank has split , to me that means at 16 plus  years old and however many K's the tanks split , I will be wise and replace it before that  happens .

V35 radiators bolt straight in and so do the air box's , what I don't know is if the shrouds swap over , I now have a V35 shroud with twin fans so will let you know .

I will get an all alloy twin row oven brazed V35 radiator that I know will bolt straight in to the M35 with the V35 airbox .

 

Something like this https://www.ebay.com.au/itm/All-Aluminum-Radiator-For-04-07-Nissan-Skyline-V35-350-GT-V6-Petrol-AT-2-Row/292747369595?fits=Plat_Gen%3AV35&epid=20024291071&_trkparms=ispr%3D1&hash=item44291a5c7b:g:39IAAOSwlY1ZGWtm&enc=AQAEAAACcIQvEcHUrT7nmUC3yY5qbPyaBN1nJEDYW8MyypsJPgXKMy1HQ5tqr4SizEZhU4A6p24OFt7rJh%2BdO2BEZmEPDW6%2FdjjBov%2BrSFU6l4fpRZl7yhLriYPIhwb7o5FTsYdxhb9OKP7OwzPAHwluI1Sgu7m90%2FJPzyf2KcEfSjKUMNNKb4k%2BofdpFVGNxlyCFrTifEPDiNBvEEBjcAXw1LOVimMAgz4L7jUqvyNWZDqGbQLSyDilZWixkqP1436m56%2BGjFdTTX5UVnMTVXDkoWUck0NTxUcJ%2B5bGmCEkPrY%2FjDy6vEkNus0sKE2OBmzG%2FJiIOE9co5hh2aohSc%2BK41SCIyXWZTbKNNzPAVutlMBYgNxti7b3haPUaQQ8%2B4xmSI%2FkPiEPaVL0p44yOLc9SkkyOCQYtAZ66xYDg1unRrLPjk32Q7u8KOA3oa2Z%2FFtRoZXsKQfGYjUMV0pxmsymTuXNTSxg5XWoeiYBH9LO4gYJQZP7LN6jYG%2BFVKdy8De1U5sLXIun5W2GPd0o7DUnwseEJFakrTVqSMPRGnAvGwIZhAwj0YcZnDpI6Oan9F2sPxeMssVAO1rVzutwd8vvtp9DWe5kiDZQ87JLvcGm%2FllcWoLwHeHBLngW1KqB%2BLZC3CsQK3a%2Bil11ZYxfh9kJptOLYj3eQSdQDc09n%2Bj08iBLckScUmQVTqzyzI28EogKLspt8l56KynEiZvVlRkxRsUhhyWjXikj0xVkTc6ZBPvsbkWXK8Ve2VjuvsY4mP188zjS71cfxpsaKd2hVZOKLc7hUDXrqeiBHjFbHErgxvoEuFI1b1sYCIAUvLSOYcd72XzYAQ%3D%3D&checksum=292747369595139f4f688d414f178dd6023d81e75d32

I would think that a radiator made to replace the V35 radiator would take the same shroud and I have used ebay radiators before with total success .

As to the V35 electric fans I will let you all know how it all goes...good or bad .

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Given you're running a 2.8 and my 2.5 is not really like for like, I suspect there could be a bit more timing you could give it. What is the kW yield per degree you're putting through it? Here's my E85 map to give you an idea, where it was I could still get another 3~4kW per degree thrown at it.  
    • It turns out that Setrab make a fan specifically for the oil cooler which is great and I've installed it with minimal swearing. I removed my 2x 12in push fans from the front of my aircon condenser and wired them into this. My main thermo fans kick on when I use the aircon anyway and would effectively already be working as puller fans through the condensor which is infront of the rad. The push fans (understandably) didn't really do much in the config they were previously in so now they're out. Now we're on to the "Oil fan doesn't really do much either!". Yes I'll duct it next if it does nothing in heavy use which it shouldn't. But hey, the object exists and fits great and is cool. Let me have this. The car is still in the "do my fittings leak oil now? do my wheels actually rub?" phase. I did a spirited drive on them and didn't hear or feel anything. Then I got back home and noticed there were grind marks on the inside of the rims, though I couldn't see where they were touching I got out the grinder and attacked the suspects. Note: I do not know how to use a grinder. Then I realised I had dragged my new rims across my concrete driveway before I did this drive. I didn't think I had damage at that time when I briefly looked...... but remembered this occurred after I did all the angle grinding. The grinding on the wheels in some very specific spots. It's not around the whole rim for example, which lines up with dragging it across concrete more than hitting a suspension component for even 1 full rotation. So everything is currently painted and taped up and I need to test it some more to see if it really IS rubbing, but from inside the car it doesn't feel like it is. In other news I attempted to do a before and after comparison of the heads/cam upgrade thing. Dynos lie, everything is in different measurements. Here is the data from the sandown back straight. Car go faster than before. Vroom vroom.
    • Here's my base ignition. +3 correction to redline when shooting water/meth which is always on. Looking at my old ignition table, I should be able to add 1-2 degree's next time I'm on the dyno.  Let me know your thoughts. 
    • Given what I know now - same haha, but this was 12 years ago with second hand 740cc Nismo injectors in my S15 daily, I was too busy hunting elsewhere for the issue to even look at the injectors, running through some cleaner was a happy coincidence haha
    • Not a terrible idea. But if I ever had concerns that my injectors were sufficiently dirty to be causing me a problem, they would be out of the engine and onto the actual injector cleaner/testing bench.
×
×
  • Create New...