Jump to content
SAU Community

Recommended Posts

I need to replace the high pressure line from the pump to the transfer case since it's leaking (PN 41706), car was bucking under WOT acceleration and removing the AWD fuse resolved it.

I'm wondering if anyone knows the best way to replace the line without spilling fluid everywhere? Is there a way to fully drain the ATTESA system or do I just unbolt the line and hope I have enough brake kleen to get it all after?

Also, regarding fluid. I've poked around on the forum but haven't seen a solid answer. I can't seem to get my hands on Nissan Power Steering Fluid Special, so I was thinking I would just go for Nissan Matic D since others have had good luck with that, unless someone knows a place that will ship PSFS to Michigan, US?

I included pictures of the leaky line and the diagram I pulled the PN from in case I got the part number wrong.

 

page_350_asterisk_002.png

IMG_20200830_111122.thumb.jpg.58fd7cccea15d64ee673cb0f45e32a60.jpgIMG_20200830_111136.thumb.jpg.3bf3c7fcb6fdd269c52c0b2b1f76c60c.jpgIMG_20200830_111146.thumb.jpg.0b6ac6a7db60ff911ca4911f9579318a.jpg

image.png

Edited by SGT Grumbles
wrong image

It's not exactly clear from the pics which line it is, so I can't confirm part#.  However, it is unusual for those hoses to leak (of course nothing is impossible). I'd undo and then nip up the banjo bolt at the each end of the hose, and also the flare fitting at the back of the transfer case. Then degrease everything and check again after some driving.

If there is a light leak there, it's not the cause of your 4wd problem, there is nothing major in those pics.

If you replace that line you will need to refill the boot reservoir and rebleed the system. You can use any  good auto trans fluid, I use Castrol Syntrans in the race car but I don't know if that's available where you are. You could use a syringe to pull fluid out of the boot before you undo the line if you want to minimise the fluid that runs through.

 

Looking at it again last night with the top diagram, I'm pretty sure that's the right PN. I'll try loosening and re-tightening the banjo's just to see, but it looks like it's coming directly from the rubber portion of the line. You're right though a clean should help pin-point it.

Last night I tried topping up the system with some Castrol Dexron VI ATF. The AWD ran better but still felt like it was surging/slipping. I checked the reservoir and the fluid level was the same as when I filled it.

Is the surging/slipping when the AWD engages a typical sign of a different problem? I thought I lucked out with a leaky line. I'm hoping it's not the pump since those appear to be rather pricey.

In the meantime is it safe to cruise the car with the fuse pulled or does that risk wrecking the front/center diffs?

I'll take a look at the sensor tonight after work, see if I can see anything up with it. I know there is one guy with a GTR nearby, may see if he'll let me borrow his for a day.

Sounds like your transfer case is stuffed if it is slipping. Your friction plates are probably worn. It is completely possible to tear the material away from the plates due to incorrect or poor fluid.

On 01/09/2020 at 7:35 AM, Duncan said:

You can use any  good auto trans fluid, I use Castrol Syntrans.

Castrol Syntrans is a gearbox oil and is the correct oil for the gearbox, not the transfer or Attesa. Transmax Z is the ATF that should be used inside the transfers. Attesa fluid can be anything ATF basically dex iii upwards as it is just a hydraulic actuation fluid after all.

Also regarding any new Attesa hoses they are mostly all discontinued from Nissan and is now only available part of the Nismo heritage lineup.

22 hours ago, TXSquirrel said:

Your issue may also lie in the sensory side and not mechanical side.  What's the condition of your G-sensor?  Can you find another one nearby to test?

Just checked, one of the previous owners swapped it for a digital one. Looks pretty new, so I'm guessing that's not the issue.

14 hours ago, BK said:

Sounds like your transfer case is stuffed if it is slipping. Your friction plates are probably worn. It is completely possible to tear the material away from the plates due to incorrect or poor fluid.

Castrol Syntrans is a gearbox oil and is the correct oil for the gearbox, not the transfer or Attesa. Transmax Z is the ATF that should be used inside the transfers. Attesa fluid can be anything ATF basically dex iii upwards as it is just a hydraulic actuation fluid after all.

Also regarding any new Attesa hoses they are mostly all discontinued from Nissan and is now only available part of the Nismo heritage lineup.

Man that's a bummer if that's the issue. I'll drain and replace the trans/transfer fluids and see if there are any plate bits in there. Based on how the car feels when AWD engages I wouldn't be shocked if the clutch pack is worn out. Figured it had more life since there is only about 96k km's on it (assuming no rollback).

Are there any transfer case rebuild kits out there? I wasn't able to find anything when searching. Luckily there is a place nearby that rebuilds R32 GTR transfer cases if there aren't decent kits.

I'll let y'all know how the new fluids work out...and start budgeting for a transfer case rebuild lol. Oh well good excuse to swap clutch/fly wheel and get a new down pipe.

IMG_20200902_095002.jpg

Yeah digital G sensor should be maintenance free.  Previous owner just saved you $400.

Your issue is mechanical then.  I was thinking, however, if the transfer case was slipping, why would it buck the car?  Because the rear wheels are still pushing, just the power not transmitted to the front.  So I would say do a quick check on the front diff. also, just make sure there is enough fluid and also the right fluid.  

On 9/2/2020 at 9:40 PM, GTSBoy said:

Yeah. Nah. There is no such thing as an R32 with only 96 kkms. They all had at least that much 15 years ago.

a man can dream...lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...