Jump to content
SAU Community

Recommended Posts

Looking for a little electrical help. I have a hcr32 on a Nistune ecu that at first, had problems with holding connection to the software even with the key only in the on position with the engine off(so not an electical noise issue). Now, I cannot connect to the ecu at all with Nistune, or data scan software. I have tried different cables, different laptops, even re-wired a new consult port in. After that I tired the paper clip jump trick to get codes to flash and nothing worked. I have just got another oem ecu, and still have no luck. I’m quite stuck now and id appreciate any help. Thanks

Edited by smart_garrett
Link to comment
https://www.sau.com.au/forums/topic/481195-no-ecu-working/
Share on other sites

19 minutes ago, robbo_rb180 said:

Does the car start and run?
If ecu is not getting power check ECCS relay and associated fuse

If just a communication issue test the continuity of the wiring from the consult port to the ecu

The car starts and runs great. I also tested the wiring from the consult port to ecu and everything was good, even rewired a new port and still no luck.

Edited by smart_garrett
Link to comment
https://www.sau.com.au/forums/topic/481195-no-ecu-working/#findComment-7940544
Share on other sites

ok, double check the continuity/resistance of the consult plug wiring and correct connections at ecu and port.
Have a re-read of this Nistune Diagnostic/Connection issue guide
https://nistune.com/docs/Installation_and_Communication_Diagnostics.pdf

consult port wiring guide
http://nistune.com/docs/MAF_and_Consult_pinouts.pdf

for it to be an issue with the factory ecu in my opinion it is a wiring/pinout issue

Link to comment
https://www.sau.com.au/forums/topic/481195-no-ecu-working/#findComment-7940547
Share on other sites

8 minutes ago, robbo_rb180 said:

ok, double check the continuity/resistance of the consult plug wiring and correct connections at ecu and port.
Have a re-read of this Nistune Diagnostic/Connection issue guide
https://nistune.com/docs/Installation_and_Communication_Diagnostics.pdf

consult port wiring guide
http://nistune.com/docs/MAF_and_Consult_pinouts.pdf

for it to be an issue with the factory ecu in my opinion it is a wiring/pinout issue

The consult wiring guide is the guide I used to rewire my consult port to a new wiring specialties pig tail. I have 12v and a ground, but I’m not sure what I should be seeing at the Rx, tx, and clk connections, if anything.

Link to comment
https://www.sau.com.au/forums/topic/481195-no-ecu-working/#findComment-7940548
Share on other sites

14 hours ago, GTSBoy said:

Nothing that you can see with a multimeter. That's a serial link. You're talking digital data at many kbaud.

That’s what I was thinking that’s why it’s hard to see if it’s receiving or transmitting data. 

Link to comment
https://www.sau.com.au/forums/topic/481195-no-ecu-working/#findComment-7940614
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...