Jump to content
SAU Community

Recommended Posts

So I have a s1 r33 . I have only spark and pulse on cylinders1 and 3 while the car is running I pull the plug on each cylinder and injector while running only 1 and 3 do anything.. tho I have pulled the coils out tested it seams to have spark on all coils also pulled the rail off an all six pulse fuel out. bench tested the injectors for pulse an resistance all seem fine the numbers were all the same 11 or 12 ohms i believe.. what could this be ecu? 

Any help would be good.. first time using forum so apologies.. 1st off my car starts..., idles ok but it's definitely not on all cylinders how many I don't no.. like I said engine doesn't change idle speed when I pull the power supply plug on injector 6,5,4,2 or coil 6,5,4,2 

OK, so now we're a bit more clear. When you said "only have pulse on 1 & 3", that's not true, and it was conflicted by what you said in your first post "pulled the coils out tested it seams to have spark on all coils also pulled the rail off an all six pulse fuel out".

What you really meant was "all cylinders except 1 & 3 appear to really suck".

Could be that those other 4 injectors are too dirty to give you a decent dose, the spark plugs are shitty, the compressions are actually really shit and perhaps masked by oil in the cylinders, etc etc etc.

We are not going to be able to remote diagnose this. I suggest you either take it all apart yourself and see what's inside, or take it to a mechanic for a little bit of directed and effective diagnosis.

When you pulled the spark plugs out to do the compression test, what did the plugs on cylinders one and three look like compared to rest? Did you put the same plugs back into the same cylinders after the compression test?  Have you tried new spark plugs?

You said you had power to the coils, use a LED test light to check to see if the computer is switching the earth at the coils. And/or use a noid light to check for injector pulse and report back your findings.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
    • Hello everyone, I am happy to join you.
    • Whereabouts are you, that looks exactly like Akira's old car....
×
×
  • Create New...