Jump to content
SAU Community

Recommended Posts

I was having a new fuel pump put in my r32 GTR and the shop says they found rust in the tank and it will likely need to be replaced. I know the fuel tank in the r32 GTR is plastic, but is there metal baffling or something else irreplaceable inside that could be rusting that would cause me to need a new fuel tank?

Link to comment
https://www.sau.com.au/forums/topic/482178-rust-in-r32-gtr-fuel-tank/
Share on other sites

The crap has most likely come from a combination of bad fuel and deterioration of factory fuel filter. I have seen a factory fuel filter corrode at less than 10000km after cutting them open if they've been on there awhile. Possibly also inspect your fuel rail for rust too as the factory ones can also  corrode.

Just take it out and clean it with bleach, it will come up new. Absolutely do not replace it if it isn't split and leaking. (I have split 3 over the years)

I agree it’s likely dirty crud that’s made it’s way back to the tank via the fuel return. The fuel pump holder/pickup baffle thingy is plastic. The only metal in there is the pump and wiring and clamps. 

I’d do the same as BK suggested. Take it out, clean it, flush out the fuel lines and replace the fuel filter. 

Maybe double check it is a plastic GTR tank. 32 GTST tank is steel and I know people have fit GTR tanks into 32 GTST but I’m not certain if the GTST tank fits in a GTR, but it might.

33 minutes ago, Beer Baron said:

I agree it’s likely dirty crud that’s made it’s way back to the tank via the fuel return. The fuel pump holder/pickup baffle thingy is plastic. The only metal in there is the pump and wiring and clamps. 

I’d do the same as BK suggested. Take it out, clean it, flush out the fuel lines and replace the fuel filter. 

Maybe double check it is a plastic GTR tank. 32 GTST tank is steel and I know people have fit GTR tanks into 32 GTST but I’m not certain if the GTST tank fits in a GTR, but it might.

Holy shit, what blast from the past - the Beer Baron is alive ! Great to see you back mate !

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...