Jump to content
SAU Community

Recommended Posts

Purchased my 95 R33 recently and I bought it knowing the blower motor did not work. Pulled the dash a couple of days ago, which was pretty fun actually, and turns out I didn't have to go that far as the issue was quite clear once I got close.  Some previous owner cut the wire to the harness all together!  Any ideas why someone would do something this dumb? I should be able to rewire it pretty easily, but the fact that it's been cut like this scares me quite a bit.

 

Included pic of dash removed just for giggles. I'll likely create a separate post for the other scary looking things I've discovered. There are some extra wires around. Some are for what appears to be an aftermarket alarm or key fob setup and maybe aftermarket stereo stuff...?

20210814_115400.jpg

20210813_155511.jpg

Link to comment
https://www.sau.com.au/forums/topic/482738-r33-gtr-hvac-blower-motor-issue/
Share on other sites

Might have been a turbo timer....big 'go fast' must have in the early 2000's 😂

At least you have the chance to have a good look at what lies beneath while the dash is out, hope all your fixes are as easy for you as the cut wire one.

Sadly fixing the wire and plugging it back in didn't work. Ordered another blower motor from the UK and a brand new fan controller amp. The motor didn't turn on either, so hoping the fan controller amp does the trick. It arrives tomorrow. The confusing part is that there is definitely power getting to the motor.

On 8/22/2021 at 7:19 PM, GTSBoy said:

Most loads are switched on the earth side, meaning that there is usually power at the load itself.

Interesting. Good to know. Again, praying this stupid fan controller amp does the trick. Any good way to test the earth side?

On 8/23/2021 at 9:59 AM, BlueBOB said:

Any good way to test the earth side?

Yuh. Get the wiring diagram and work out where the power comes from and what has to work (wiring, switches, relays) between the +ve supply, the load and the -ve rail for the motor to switch on. If you can prove to yourself with basic electrical diagnostic techniques (checking for continuity, measuring voltage at different points in the circuit, confirming that switches open and close when required, etc) you will either find what is not allowing it to work or you will eventually come down to the motor/load being dead.

  • Like 1

All fixed!  Obviously the wiring harness being cut was a problem. With that repaired, I was able to test it was getting power as previously noted, but still no fan.  Based on research I had ordered a used blower motor from the UK off ebay and a brand new Fan Control Amplifier which a number of posts claimed to be the sneaky issue (ebay link to part below).

 

JDM Nissan R32 Skyline S13 Silvia Blower Fan Control Amplifier 27761-01U00

 

I received the blower motor first and when I plugged it in, still no fan.  The amp arrived a few days later and that was the culprit.  The interesting thing is that this part is the part number for the R32, however one post I read indicated that the R32 part would fit in an R33 and I had all kinds of trouble finding the R33 part number for some reason.  This part fixed the issue immediately and all is well. I also had to repair my actuator motor like so many others have to do.  Now I get to have the fun of putting the dash back together.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi GTSBoy, Excuse my ignorance but what does a "Bad" Knee point mean ? 
    • HFM BM57 has a "bad" knee point, IIRC. It's not the same thing as the later R chassis MC.
    • The ATTESSA is functionally identical to R34; there were a bunch of JDM models that continued ATTESSA including Fuga/Q70, Skyline/Q50, Cima etc as an option. All with Auto only and I think mostly for snow regions. AFAIK there were no AWD VR30DDTT sold in Australia - it is on my to do list to check regs for racing a LHD car in Targa/ATR/AASA/CAMS events because if I can get the auto to work it would be interesting to run a 4wd car The Ecuteck TCM tuning is the same model as their ECU tuning, they already have it for R35 and Dose's favourite, BMW. You buy "points" to allow your computer to be tuned, buy either a bluetooth (phone app) or bluetooth+USB+Key (phone and PC) dongle, and pay for a tune that will be locked to your tuner ( ). You can also access the tuning software yourself but 1. it is mega expensive and 2. these computers have a billion parameters that intersect, so how could you ever spend enough time on it to get a decent result.
    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
×
×
  • Create New...