Jump to content
SAU Community

rb25det r33 unstable idle + hesitation + black smoke / error code 54


Recommended Posts

Hi everyone,

I've done some searching on the forum, however couldn't find something which exactly matches my issue or has solved it.

The issue is relating to unstable idle on start up where revs fluctuate and black smoke can be seen from the exhaust with a noticeable fuel smell.

After about a minute, the revs will start to stabilize but if gas pedal is pressed it worsens the rev fluctuation. soon after plugs become sooty.

Note: I've attached a video of what happens

 

Troubleshooting I've done so far:

  • CTS replaced, tested wiring (good ground and other wire giving 5volts)
  • adjusted timing to 15 degrees
  • checked for vacuum leaks around the intercooler pipping and engine bay > measured vacuum at -17hg
  • changed plugs
  • MAF sensor tested (signal wire showing voltage change, car stalls when unplugged)
  • coils tested (engine hesitates when each one unplugged, resistance testing consistent throughout the 6)
  • tested with o2 sensor plugged and unplugged

 

Car was running fine a week ago. in some cases if i unplug the battery and clean the plugs it runs smoother.

The car is running a stock ecu and at times throwing error code 54 on the dash which is A/T Control.

It has a manual transmission but i realized the ECU is for automatic (MEC R531 A1 4225)

Could this be possibly causing the issue?

As you can see I'm currently running out of ideas looking for some possible causes/solutions.

Thanks

Ray

 

 

 


 

 

 

 

 

 

On 9/21/2021 at 4:27 PM, CUR33 said:

It has a manual transmission but i realized the ECU is for automatic (MEC R531 A1 4225)

Could this be possibly causing the issue?

No. It'll be fine. But you should set the timing to suit the ECU, which probably wants 20°, being an auto. Not a big issue, you're just running 5° retarded.

Check your fuel pressure.

 

 

On 9/21/2021 at 6:21 PM, GTSBoy said:

No. It'll be fine. But you should set the timing to suit the ECU, which probably wants 20°, being an auto. Not a big issue, you're just running 5° retarded.

That's good to know, i did end up adjusting the timing to 20° to help with idling issues.

On 9/21/2021 at 6:21 PM, GTSBoy said:

Check your fuel pressure.

I currently don't have a fuel pressure gauge to check.

But i did check that the Fuel pump primes and the pressure build up in the lines can be heard just before the pump stops.

Also when i open the filler cap it makes a 'tisss' sound.

 

The issue is:

Black smoke from exhaust

hesitation/rev fluctuation

- spark = yes

- coils = good

- FPR = untested

- Injectors = untested

- fuel filter = good

I'm started to think the issue could be relating to the injectors or fuel regulator.

more testing tomorrow to try and identify the issue..

On 9/23/2021 at 8:32 PM, GTSBoy said:

Check that it is not too high, not that it is too low. You will need to use a gauge.

I ended up testing with a gauge. On prime fuel pressure jumps to 50psi then back to 0.

See video.

i tested with another fuel rail and the same thing happens. The pressure doesn’t hold in the lines and dropped after fuel pump stops.

After changing the rail car is not starting, when cranking I noticed the cat overheat warning light comes on. Might need to check if the Cat is blocked.

So there are the issues:

- car no longer starting

- not holding fuel pressure on prime

- cat overheat warning light (might be blocked)

274D03EB-F396-4E5E-94CC-ED6C8C4ED99E.png

On 9/25/2021 at 10:21 AM, CUR33 said:

On prime fuel pressure jumps to 50psi

Maybe a little too high.

On 9/25/2021 at 10:21 AM, CUR33 said:

then back to 0

How fast?

On 9/25/2021 at 10:21 AM, CUR33 said:

After changing the rail car is not starting

What do you mean, "changing the rail?"

On 9/25/2021 at 10:21 AM, CUR33 said:

I noticed the cat overheat warning light comes on

Also used as CEL. Now you have a code to investigate.

On 9/25/2021 at 10:21 AM, CUR33 said:

(might be blocked)

Yeah, nah.

On 9/25/2021 at 11:14 AM, GTSBoy said:

How fast?

Straight away (as per video)

On 9/25/2021 at 11:14 AM, GTSBoy said:

What do you mean, "changing the rail?"

i replaced the rail with another one, complete with injectors and FPR. After installing, car won’t start.

C6F1E0C0-A73E-443C-9B15-3F4E4AE98E3F.thumb.jpeg.6cb8b25d9345a9e912af28ab24959c82.jpeg

On 9/25/2021 at 11:14 AM, GTSBoy said:

Also used as CEL

By CEL do you mean relating to an ignition problem?

the ignition loom was converted from series 1 > series 2 and ignition coils changed to s2 ones with the (igniter at the top)
 

I can confirm the 1st 2nd and third plug is giving spark. (See pic)

90B27582-270A-403B-AE6F-87BB6071385E.thumb.png.fbb77ef18f882794eda45bb90c22296b.png

More checks:

- cat = removed not blocked

-  coils = Resistance test relatively consistent on all 6 

- spark good tested on cyl 1, 2, 3 (by grounding to the rocker cover) 

- still investigating why cat overheat light started turning on when cranking.. 

 

I don't generally watch videos posted in these threads as they are almost always useless.

CEL = Check Engine Light.

 

Something you did wrt the rail swap is wrong, or the injectors or FPR are faulty. Put back the proper stuff. Don't report fuel pressure behaviour on different equipment to that which possibly caused the problem without first reporting the behaviour on the original equipment that was on the car when reporting the problem.

Also worth noting - The videos don't seem to work (at least when I clicked on them)

Troubleshooting methodology is better than most Mr GTSBoy 😛

Generally though - Why swap a rail? How could a rail fail other than it leaking? And if it leaks with 50PSI you will absolutely note it is time to replace the rail.

Fuel pressure doesn't stay indefinitely. It also doesn't drop away straight away. I doubt we have a tunable ECU in there to see what is going on, in which case you'd better make sure you're running stock injectors, stock rail, stock FPR and basically stock everything if you're going to use the stock ECU's error codes to diagnose stuff.

On 9/27/2021 at 9:13 AM, Kinkstaah said:

Why swap a rail?

I had access to spare rail which included the injectors and FPR. That way if the issue was relating to a leaking injector or FPR issue it would be sorted. 

However the fuel pressure it still not holding.
iv changed the FPR as well and no luck.

 

note: old fuel rail setup has Since been reverted back

We know that there is definitely a fuel pressure leak.

fuel leak down test = failed (pressure drops instantly)


The question is where is the leak occurring..

possible causes

injectors = no leak from any while priming

FPR = tried to pitch the short hose on the FPR while pump was priming and the pressure shot up to 100psi but after pumped stopped went back down to 0

F6CB4351-46B2-4FCD-A613-0BF51C8D2439.thumb.jpeg.c7c06d98046d5c6e674defe7efd88967.jpeg

In saying that iv tried another FPR with the same result.

Either the 2 FPRs I have are faulty or something else is causing the Pressure drop.

 

Fuel tank lock ring 


One other observation is that The lock ring where the fuel pump goes in the boot is split. fuel pressure might be escaping from there.

 

349AD4B7-12E7-4826-B74F-EDEFD60769E9.thumb.jpeg.b8d3a50efd19ecbc3650f8cbb0ec3c99.jpeg

 

I’ll replace this first and see if that changes anything.

 

The pressure should drop. Maybe not instantly, but it should. It doesn't just hold the pressure indefinitely when the engine is off and the fuel is not pumping.

If it did, there would be no need to prime the fuel system... ever. If the pressure is dropping or being too high (or really, fluctuating) while the engine is running then there's an issue with the FPR.

If you have two sets of stock injectors, and two stock FPR's and two fuel rails, I wouldn't be chasing the fuel side of the engine bay at this point for your problem.

Personally I'd be re-checking that MAF (is it the same auto/manual/is it clean? did you actively clean it with MAF cleaner?)

Alternatively, anything else custom in that circuit?
You have spark, but do you know you have spark at the right time?. You've set timing to 15deg, but have you checked it with a timing light? Could it be out? Whats your CAS doing?

On 9/27/2021 at 12:44 PM, Kinkstaah said:

Personally I'd be re-checking that MAF (is it the same auto/manual/is it clean? did you actively clean it with MAF cleaner?)

yes the MAF was cleaned, voltage was checked (12v, signal voltage and ground are good)

 

On 9/27/2021 at 3:42 PM, GTSBoy said:

Check valve. It'll be the check valve.

That's what i'm starting to think. The check valve is in the fuel pump (Walbro 255). I will be replacing the whole pump.

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...