Jump to content
SAU Community

Recommended Posts

Hi all, just got back from the track today, after the last run I noticed a whining noise at idle, like straight cut gears but not quite so high pitch. It's pretty loud. With my foot on the clutch there is no noise and there is no noise on deceleration. I noticed it would get louder and higher pitch with engine speed until the point where engine noise drowns it out.

The gearbox (30A) was installed a few thousand kms ago, it's had one oil change. I used a second-hand Nismo clutch/ lightweight flywheel kit in the install, the condition was average on installation with the clutch approximately more than half-worn. The lightweight flywheel seems to rattle a bit more as of today but maybe I'm imagining it.

I would normally associate this with input shaft bearing noise, from reading other noise-related gearbox threads. But surely not, not after this amount of time? The car is going to the shop in a week for some brake work so I will ask for my mechanic's opinion then; going in with some other opinions would be helpful.  

I changed the oil not so long ago and there’s been no indication of any leaks. I was under the car on Saturday and it was clean so unless it came out over the last couple of days, clung entirely to the underbody and didn’t give off any smell. I’m gonna say (pray) it’s still in there. 

I had a similar issue with a new box after 1 track day. When I drained the oil, it told the story. Let's just say it glittered like gold.

Im not sure exactly what went wrong as I didn't have it pulled apart as the nice chaps at Nissan where nice enough to replace it with another new one. Thank you Mr Nissan, I bow down to you.

 

I'm assuming it was a broken/stripped synchro. It was still selecting and had drive in all gears but was making a whine noise. At first I thought it was a bad turbo bearing but then realised the noise went away when stepping on the clutch pedal. From memory I think the whine got quieter in 4th gear.

 

Sounds very similar to what you're describing, hopefully not.

  • Like 1
On 11/30/2021 at 2:06 AM, r32-25t said:

First thing I would do it drain the oil and see what it looks like. 

On 11/30/2021 at 5:51 AM, admS15 said:

I had a similar issue with a new box after 1 track day. When I drained the oil, it told the story. Let's just say it glittered like gold...

I'll take the oil out next Monday and have a look - fingers crossed. 

Anybody have any experience with Nengun refunds/exchanges?  

 

Or could be someone put in the thrust bearing in backwards and now it's stuffed, although a cheap part to replace the labour cost more.

Dump oil first, then next box off inspect thrust / throwout bearing whatever it's called these days 

  • Like 1

Cheers guys. I’ll mention this to my mechanic on Monday, luckily he performed the work which helps in the way of warranties - hopefully. 
 

I’m at the very least annoyed about the US$100 cost of the oil but given that pales in comparison to the cost of a new gbox, I’d be relieved if this doesn’t cost me another US$2k.

I’ll update with our findings. I’ll also get a video clip for others to use as a sound reference. 

  • Like 1

Here's a video I took to capture the noise. I am engaging/disengaging the clutch in the video, also attempting to do it slowly to hear the change in pitch when the transmission begins rotating. It doesn't sound promising.

 

 

Should wind back your odometer so when you deregister, it has low kms on it.

You know us Australians froth over low KMs, even if it means nothing at all.

  • Like 1
On 12/3/2021 at 9:26 AM, Dose Pipe Sutututu said:

Should wind back your odometer so when you deregister, it has low kms on it.

You know us Australians froth over low KMs, even if it means nothing at all.

Hahaha, I like ‘em high, another deterrent for the thieves over here.

  • Like 1
  • 2 weeks later...

Hi all,

Took the car in to the shop to diagnose the gearbox noise. The mechanic was pretty sure it was the gearbox from the off, although he said the noise was much louder from the bellhousing and noted the possibility of it being the release bearing. He took the box out, tried a new release bearing to no avail, drained the oil - which looked incredibly metallic - and stated it's the box. Which is pretty much all there is to it - further opinions welcome.

I took pictures and we made a video documenting our findings - yeah that tray was clean before.

 Video: 

 

IMG_1391.JPG

IMG_1399.JPG

IMG_1382.JPG

Edited by GoHashiriya
  • Like 1

I had to keep this quiet as it's been a long-winded battle of blame between myself/my mechanic and Nengun/Nissan. But in short, I was refunded for this box. I have placed an order for a new one - prices have gone up 20% since June and there's a 3-month wait. In the meantime I'll be using this box, hopefully drive a few more events on it then swap it out in March/April.

I appreciate all your opinions, it helped when talking with my mechanic. I would love to determine what has gone wrong  but I'm not expecting it to be determined quickly.

On 12/14/2021 at 8:57 AM, r32-25t said:

That oil looks pretty thin, bet they used synthetic oil which these gearboxes absolutely hate 

The OEM stuff was swapped out at about 800kms with Castrol Syntrans (TAF-X) 75w-90 GL4+, pretty sure it's fully synthetic. During the recent diagnosis I swapped it back to Nissan GL4 75w-85.

You're right, it looks like p*ss. 

On 12/20/2021 at 5:53 PM, GoHashiriya said:

I had to keep this quiet as it's been a long-winded battle of blame between myself/my mechanic and Nengun/Nissan. But in short, I was refunded for this box. I have placed an order for a new one - prices have gone up 20% since June and there's a 3-month wait. In the meantime I'll be using this box, hopefully drive a few more events on it then swap it out in March/April.

I appreciate all your opinions, it helped when talking with my mechanic. I would love to determine what has gone wrong  but I'm not expecting it to be determined quickly.

The OEM stuff was swapped out at about 800kms with Castrol Syntrans (TAF-X) 75w-90 GL4+, pretty sure it's fully synthetic. During the recent diagnosis I swapped it back to Nissan GL4 75w-85.

You're right, it looks like p*ss. 

I'm surprised you got a refund. I would have figured that between the gearbox being sent overseas and your mechanic likely not working for a Nissan dealer they would've told you to pound sand.

On 12/21/2021 at 11:34 AM, Dose Pipe Sutututu said:

Samsonas or BMW DCT or ZF8HP 

no more gearbox issues.

The costs are certainly heading in that direction. Hell, I already commited to financial ruin by buying a Skyline in the first place.

On 12/21/2021 at 1:24 PM, joshuaho96 said:

I'm surprised you got a refund. I would have figured that between the gearbox being sent overseas and your mechanic likely not working for a Nissan dealer they would've told you to pound sand.

Perhaps it was a different story as I am based in Japan. I agree with the latter remark about my mechanic not being a Nissan dealer though. 

  • Haha 1

Great result and Nissan/Nengun was pretty speedy with the refund. My saga dragged on for 9+ months before a replacement landed on my doorstep.

Surprised they're letting you keep it.

 

  • Like 1
On 12/21/2021 at 3:57 PM, admS15 said:

Great result and Nissan/Nengun was pretty speedy with the refund. My saga dragged on for 9+ months before a replacement landed on my doorstep.

Surprised they're letting you keep it.

 

I was expecting the same. The box was on the floor at my mechanic’s and everyone was getting annoyed. I figured there’d be no resolve, ordered a new transmission, and put the noisy box back in. When factoring-in what I sold the old 71c for I’m about even, there’s a slight loss when considering the new transmission. 
 

If I ever figure out what caused this I’ll update this thread. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...