Jump to content
SAU Community

S1 C34 Which Braided Front Brake Lines for Z32 Conversion

S1_C34

By S1_C34,
in Four Door Family & Wagoneers

 Share

Recommended Posts

S1_C34 Apprentice

S1_C34

Posted
Posted

Hello,

I've done some researching on this site that has been helpful so far.

I understand that Z32 / R32 front brakes are a direct bolt on to S1 Stagea. There's an orifice of sorts you need to remove.

Quote

I found that they fit perfectly on my S1, just had to remove a little orifice from the fluid inlet and I was able to use my standard brake lines with banjo bolt,

Quote

stock stagea brake lines bolt into the fittings, if you remove the flare fitting from the caliper, but are a bit to short and the lines are pulled too tight once fitted, so get a set of new custom length lines or braided lines.

So an orifice on the calipers themselves. I have reproduction Z32 calipers already in storage.

Honestly I have no problems just keeping the stock front brake lines and removing the orifice and throwing on Z32 calipers / rotors / pads. Cheap, cheap upgrade.

But if I can find some braided lines for less than the cost of the calipers, I would be interested. And if I get the right braided lines I wouldn't need to remove the orifice from the calipers right?

nissan-462110v002-1567861769531-big.jpg

S1 C34 25X brake line diagram. Front brake lines highlighted.

S13/14/15 Silvia > 300zx Adapter Brake Lines - https://au.gktech.com/s14-s15-to-z32-skyline-conversion-braided-brake-lines

One of the reviews: 

Quote

Great, product also works from going from C34 Stagea RWD to Skyline brakes

So RWD C34 and AWD Stagea front brake lines are different according to that and those wouldn't work. Or maybe they would?

R33 GTS-T braided lines - https://us.gktech.com/r33-gts-t-braided-brake-lines

But those are almost as much as the calipers cost me so I'd probably just keep the stock ones.

Can someone enlighten me?

 

GTSBoy Grand Master

GTSBoy

Posted
Posted

I can't answer the exact question, but.... custom braided lines are not hard to organise. I'd just front up with measurements of the two parts of the hose length (from body fitting to strut mount, from strut mount to caliper) and samples of the fittings needed at each end, and....wait 30 minutes.

Duncan Grand Master

Duncan

Posted
Posted

I suspect that is my long ago voice quoted there. Anyway, the point was you either use a banjo bolt end on the line (which seals with a copper washer to the calliper), or a flare nut (which seals on a removable olive inside the caliper).

Ultimately I changed across to aftermarket 8 piston brakes and have done about a bazillion klm on them since. They were a R32 gtr kit that included braided lines, bolted straight on and off I went

S1_C34 Apprentice

S1_C34

Posted
  • Author
Posted (edited)
On 7/21/2022 at 12:00 AM, GTSBoy said:

I can't answer the exact question, but.... custom braided lines are not hard to organise. I'd just front up with measurements of the two parts of the hose length (from body fitting to strut mount, from strut mount to caliper) and samples of the fittings needed at each end, and....wait 30 minutes.

You're not wrong, it would be easy enough. I'm just kinda lazy and was hoping for an off-the-shelf setup.

On 7/21/2022 at 4:21 AM, Duncan said:

I suspect that is my long ago voice quoted there. Anyway, the point was you either use a banjo bolt end on the line (which seals with a copper washer to the calliper), or a flare nut (which seals on a removable olive inside the caliper).

Ultimately I changed across to aftermarket 8 piston brakes and have done about a bazillion klm on them since. They were a R32 gtr kit that included braided lines, bolted straight on and off I went

It probably is! That last part is helpful. Thoughts on the other comment about the stock hoses being too short / not enough slack when mounting the larger calipers as the other poster mentioned? I've seen most people say it's just a bolt-on affair, and that's the only post I've seen saying there isn't enough slack in the hose when mounting the 4-pots.

Kinda just leaning towards using the oem lines to be honest, but I may give these a go: https://www.goodridge.co.uk/products/car-brake-kit-for-nissan-skyline-r32-2-6gt-r-1989-1994?variant=12842545348673

 

Edited by S1_C34
Duncan Grand Master

Duncan

Posted
Posted

I should say that the kit I fitted was for an R32, but had very generous line length (if anything a little too long, have to keep them out of the way). I didn't measure them compared to R32. standard lines, noting the standard lines have a fitting to bolt them to the knuckle.

If you can afford the risk of the car being off the road for a week, I'd try standard lines, as long as they are not taught at full droop on the suspension, I'd just use them...

  • Like 1
  • 3 weeks later...
Stagea_Neo Experienced

Stagea_Neo

Posted
Posted (edited)

I'm not sure if this helps or not.

I recently upgraded to R34 Vspec2 Brembo's on the S2 Stag.

I used this braided kit:

https://safebrake.biz/home/292-skyline-gt-r-r34-awd-26tt-brake-upgrade-safebrake-performance-hoses.html

Beyond this I got the R33gtr front brake hard lines, that go over axle hub just behind the dust plate and all lined up beautifully.  The braided lines were same length as the stock ones.

Needed to buy 2x longer bolts for one of the hard mount points for the braided hoses up the front.

Trim rear dust shields so could fit 322mm discs.

It's a pretty straight forward job.

 

ps. the r33gtr hard brake lines have the flare nut so should bolt straight into your callipers.

Edited by Stagea_Neo
  • Like 1
  • 3 weeks later...
S1_C34 Apprentice

S1_C34

Posted
  • Author
Posted

I ended up buying these: https://www.chasebays.com/products/chase-bays-fenderwell-brake-lines-nissan-r32-r33?variant=41685542764713

 

$69 USD, couldn't beat it. I'm thinking it will be a direct fit but will report back. Ordered some other stuff from that company as well that was back ordered so it's taking a while to get here.

  • 2 weeks later...
  • 6 months later...
S1_C34 Apprentice

S1_C34

Posted
  • Author
Posted

Update: I ended up having to install the Z32 calipers with factory lines as the chase bays R33 ones wouldn't work. The Stagea is missing a bracket for one of the clips on the braided lines. So I had to remove the 'olives' on each caliper which was easy. Drill self tapper in slightly and yank out with hammer. Have to be a little aggressive pulling. But yeah, just reusing OEM lines for now, no issues. It was all bolt on, not even any heatshield trimming.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      The Evolution Of "night Fury"

      By PranK · Posted

      Thats too fricken cool.
    • PranK
      Beers and skylines Fatz style

      By PranK · Posted

      That R31 was so cool. Only did Orange Park once. Scared the hell out of me.
    • GoHashiriya
      Volk TE37SL 9.5J +22 / 10J +20

      By GoHashiriya · Posted

      Selling my TE37SLs since I've switched to smaller wheels.  They're for sale in Japan but it's pretty simple to send them overseas; USA excluded, since JPPost isn't sending there at the moment. Specs Front: 18x9.5j +22 5x114 Rear: 18x10j +20 5x114 Price: 320,000 JPY/ 3,285 AUD (current FX rate) Condition: a few scratches here and there, no bends, distortions or cracks.  Tires will not be included for international buyers, I'll get them dismounted before shipping. They're currently listed on yahoo auction and will be shipped in Japan with the tires if they sell here. Shipping costs to Aus: EMS (1-2 weeks): AUD 1,175 (current FX rate) Sea (2 months): AUD 460  (current FX rate)
    • The Bogan
      NC MX5

      By The Bogan · Posted

      The alloy coolant reservoir has a sight glass, so as long as I can see coolant in the sight glass it's GTG, as for PS, it isn't anything catastrophic if it gets low, and as it hasn't lost a drop since I have owned the car I cannot see it being an issue, even after putting the "big block" 2.5 in....LOL The only time it gets slightly messy is at oil changes, as the oil filter sits above the frame, and I need to use a plastic bottle with its bottom cut off to catch the flow when loosening the filter
    • Duncan
      Single Turbo Conversion On R32 GTR.

      By Duncan · Posted

      Good on you for taking on the job, but it is a big one. Even if you have bolt on manifold and turbo, you will need: Post throttle pressure source to boost controller to wastegate (and FPR, and ECU/MAP sensor) Pre throttle pressure source to top of BOV(s) Oil feed - you can take that from the standard port in the middle of the block Oil return to block under the turbo - this is much trickier than it seems to route a decent/wide pipe past the manifold. You really can't use rubber hose because it is way too hot there, and also the oil out of the turbo core is a bit frothy so it needs to have a decent diameter Water feed - you can take that from the standard port in the rear of the block. Water return - mine runs to a T into the heater box return, just make sure you don't create a high point making bleeding hard. All of those lines should use 200 series style teflon braided hose with heat shielding because everything needs to be routed past the manifold. Also a turbo beanie is a really good idea to minimise the chance of the car catching fire (under bonnet lining in particular) You also need to decide a cam cover breathing solution as well, will you vent externally via a catch can (probably illegal) or return to the intake (plumbing required and can oil up everything over time) Keep in mind the intake and exhaust piping in the engine bay will be custom so you either need to be able to fab ally and steel or have someone you can get a car that isn't running to. Get the wideband fitting welded into the dump pipe at the same time. Also, just my opinion, a screamer pipe attracts attention and doesn't add power, I'd plumb it back if you want to be allowed to keep the car on the road. BTW do you know anything about how healthy the motor is, and what power you are targeting? Doubling or tripling the factory power on an unknown motor is a little risky. Also fuel system will need some attention (pumps, high current hanger, direct power and earth feed, injectors etc)
×
×
  • Create New...