Jump to content
SAU Community

Recommended Posts

On 23/7/2022 at 2:56 AM, joshuaho96 said:

Are you sure you don't have the neutral switch wired to the reverse switch? Could also be a DOA switch.

The switch has two wires, one wire from the loom is live with ignition on and I assume the other wire goes to the lights. When I hold the switch and plug the wires in and press the switch button the lights come on as this creates the circuit, same scenario if I swap the wires over. When it’s attached to the gearbox and I go through the gears the lights come on with every gear and off with neutral, it’s like the selector is activating it in all gears.

The switch is supposed to be closed circuit only in neutral, open circuit in all other positions. If it is closed in all other positions, then it is somehow installed wrong, or broken. How you managed to achieve that while swapping the reverse switch is likely to remain a mystery. The other mystery, which we need to solve, is why it is working backwards mechanically.

  • 2 months later...
6 hours ago, ossie cossie said:

question witch switch is witch on these pics  the one has a yellow cable tie 

thumbnail_IMG_7934.jpg

thumbnail_IMG_7935.jpg

thumbnail_IMG_7936 (1).jpg

https://nissan.epc-data.com/skyline/bcnr33/3935-rb26dett/trans/321/32006M/

https://tfaspeed.com/products/nissan-skyline-r32-gtr-gts-4-reverse-switch-assembly-32005-21u1b-jdm-genuine

https://tfaspeed.com/products/nissan-skyline-r32-r33-gtr-r32-gts-4-neutral-saftey-switch-32006-31g01-jdm

Looks like rearmost should be the neutral position switch. The one closer to the bellhousing is the reverse switch.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So....to find any R chassis part number, get your VIN (will be something like ER33-xxxxxx for you) and go to: https://www.amayama.com/en/genuine-catalogs/nissan and enter it. From there you have access to a web version of Nissan's part system, FAST. It is a bit tricky to get used to, so maybe have a shot and post up what you think.  You can also search by general model but note in some cases your car might have different options so VIN is safest.  On diagram 211 I got 14075-75T16 for Connector, Water Hose If I search for part 14053‑21U10 that you posted, that is also a water hose but not the one bolted to the plenum and 14075‑04U00 is the fitting where the water hose goes into the block.
    • Yeah now we are talking I much prefer coolers in the front middle because it lessens the chance of a small bump to a corner stopping the whole event. I was thinking the AT cooler can move out of the radiator, delete the AT/engine coolant interwarmer and mount a separate cooler with a thermoswitch somewhere further back as is common in racing, that would be one thing. Beyond that, the engine oil cooler is an obvious one to move to the wheel arch, potentially one on each side, but unused space is an issue. I did have a earlier pic with the bumper off but it doesn't show how busy the corners are: DS is full of the auto driving sensors and PS is totally fully of windscreen washer fluid reservoir But ultimately I was hoping to keep the AC, and the water/air heat exchanger is fundamental so it is not just the radiator that needs to be in front BTW here's airflow to the rad as it ran at the track (one horn is gone now and I'll remove the lights next time):
    • your right the maps for Australia came out in 2017 but are 2010 maps. i got the updated maps SD card put it in and it was the same. Same maps in my Brothers Nissan Patrol. 2020 i think his car is
    • Yeahhhh, the costs have killed me. Spent more than the cost of an engine rebuild and it most mostly servicing and a tune lol.
×
×
  • Create New...