Jump to content
SAU Community

Hi-stop Light not working

doggido

By doggido,
in V Series (V35, V36, V37 & Infiniti)

 Share

Recommended Posts

sonicii Veteran

sonicii

Posted
Posted

Mine stopped working about 6 months ago, I took it out, took it apart and found a bad solder joint.  I re-soldered that and a few other higher stress joints and put it back it, it has been working fine since.

Can't guarantee yours has the same fault though.

  • Like 1
sonicii Veteran

sonicii

Posted
Posted

:)  that is the fun part.. you can unplug the lamp from underneath the parcel shelf (access from the boot).  However, you need to remove the rear seat, so you can remove the parcel shelf, the lamp is attached to the bottom of the parcel shelf.

Maybe try having someone hold their foot on the brake pedal and ensure the normal side brake lights are on, then, push and flex the cable to the lamp (from the boot side) and see if the light turns on and off.  If it does, a bad solder joint is probably the issue and you will need to remove it to repair it.

Vee37 Collaborator

Vee37

Posted
Posted
2 hours ago, doggido said:

Checked out the above website and it looks promising so I will give it a go over the weekend.

So then, it leaves me one question, where does the red come from?

I dont have a direct answer, however, many years ago when I first got my 350GT Coupe, I replaced the front orange indicators with clear lenses. It failed the pink slip, but my mechanics didn't skip a beat, and put in orange caps inside the clear lensed indicators, and passed it without question. I guess what I am saying is, just try asking your regular mechanic. My guys didn't even check with me before doing it, they just told me when I went to pick it up.

If you want a selfie, maybe go to wreckers and find a broken red plastic taillight, and cut it to fit & cover the globes; or even a smaller upper taillight from a different car. Maybe even heat it a little to conform to a shape. Just spit-balling

GTSBoy Grand Master

GTSBoy

Posted
Posted

Yeah, well, what's worse is that the DIY link above used RGB LEDs driven to make white. They could have made red. Maybe not as bright, but then winding up the brightness by going white and then filtering down to red with the red plastic diffuser is probably going to have the same effect.

doggido Enthusiast

doggido

Posted
  • Author
Posted

 

As I was doing the rounds of the local wreckers, I found one that had a V35 in the yard which they haven't stripped yet. I grabbed the brake light out of it and got them to test which all LEDs worked. I ended up getting it for $60NZD. As long as I can at least a couple of years out of it I'll be happy.

  • Like 3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...