Jump to content
SAU Community

Recommended Posts

Hey Sau,

Long time lurker. I just wanted some opinions from the experienced guys to see if this block is still useable or if it's a boat anchor and I should try get my money back? My concern is this crack between the water jackets to the head bolt thread between cylinder 3 and 4 see picture attached. Little back story about it, I bought it as the start of a small build to put into my daily. Was told was running fine no issues the previous owner had just pulled it down to go forged bottom end lost motivation and was now selling if off, after I started to clean it up I found the crack. The target I'm aiming for would be between 375 - 450kw so not the biggest power output but as it's going into my daily ( probably in the year 2050 at this rate) I'd like to give it a chance at surviving for as long as possible. 

crack in deck rb26.PNG

As far as I know the spot that breaks most commonly is on the exhaust side, adjacent to #4 or between 4/5. So any unnecessary weakness on the exhaust side, even if it's not is the "usual" spot, can't be a good thing. And between 3 & 4 is not so far away from where the block likes to jump to pieces.

Thanks for replying so quickly and sharing your knowledge. I had heard of the block issues between cylinder 3 and 4 splitting and the crack on the outside of the block from block twist after a healthy amount of power put through them but this is all new to me. When I spotted it I thought it might be a drama but was hoping it was more superficial so I could finish making the deck flat give it a hone and get down to ordering some parts, looks like I might have to start getting in touch with the seller to try get my cash back. 

Mine has a crack from water gallery to headstud hole in-between 5&6... Sent it back together, been a year so far at 520kw and had no dramas yet .. I guess it all depends if you are prepared to do all that work to potentially do it all again 🤣

Edited by BrynDETT
  • Like 1
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...