Jump to content
SAU Community

Recommended Posts

On 24/10/2024 at 7:27 PM, Dose Pipe Sutututu said:

Sequential so 2022, DCT or ZF bruvva 

Haha I dunno about those. Something about flappy paddles that just doesnt seem right with a big angry RB. Be a man.. get a seqy! Good way of saying you have a tiny weiner :banana:

3 minutes ago, Predator1 said:

Haha I dunno about those. Something about flappy paddles that just doesnt seem right with a big angry RB. Be a man.. get a seqy! Good way of saying you have a tiny weiner :banana:

this might change your mind, long dildo shifter & paddle shifters too

 

  • Like 1
5 hours ago, Dose Pipe Sutututu said:

this might change your mind, long dildo shifter & paddle shifters too

 

Yeah nah, doesnt interest me.. plus, its pretty damn expensive. If it was around the 15k mark I would say its a good alternative to a seqy, and you would have to probably tune it with your motor as well, so additional time and costs there. At least with a seqy you dont have to mess around too much, except for things like flat shifting.

  • Like 1
21 hours ago, MBS206 said:

I want ZF, with either LS or Barra. In the cruiser.

Want more lazy power/drive for towing.

 

God I'm getting old!

You and me both.

If I ever get it running again, I'll have to look into cruise control.

18 hours ago, Predator1 said:

Haha I dunno about those. Something about flappy paddles that just doesnt seem right with a big angry RB. Be a man.. get a seqy! Good way of saying you have a tiny weiner :banana:

Wait, the flappy paddles or sequential is the small penis indicator? 

Either way, I can't afford it.

On 10/14/2024 at 10:40 PM, funkymonkey said:

So what you're saying is that you're looking for an RB30DETT for your GU Patrol

Came for OP's reintroduction, stayed for the GU discussion.  I've owned a ZD30 for 18 months and it hasn't even blown up once!  The only thing that would sound better than an RB30DETT is an OM606 but they don't exist here.

G'day to familiar faces!

On 02/11/2024 at 11:31 AM, Kinks said:

Came for OP's reintroduction, stayed for the GU discussion.  I've owned a ZD30 for 18 months and it hasn't even blown up once!  The only thing that would sound better than an RB30DETT is an OM606 but they don't exist here.

G'day to familiar faces!

G'day.

More deets on your patrol?

Unless, it's in a d22?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...