Jump to content
SAU Community

Official SAU Dyno Day V.2 Review Thread ***PICS*** v.56kdie


Recommended Posts

Well today saw the running of the second official dyno day at Unique Autosports dyno room in Castle Hill.

Though the day started slow with many people enjoying a Saturday sleep in, the carpark began to pack rapidly with a huge assortment of skylines and other high performance cars.

Congratulations must go to the individual class winners who were up against some stiff competition.

Results are listed below:

Award winners

Top RB20DET standard turbo - Silver GTS-T (R32 GTS-T) 150.6 Kw

Runnerup RB20DET standard turbo - Kinks (R31 w/ RB20DET) 144.5 Kw

Note: There were no modified turbo RB20DET's in attendance so a runnerup category for standard turbo was put in its place.

Top RB25DET standard turbo - R33vit (R33 GTS-T) 197.6 Kw

Top RB25DET modified turbo - B-Man (R33 GTS-T) 327.9 Kw

Top RB26DETT/RB30 standard turbos - Dave (R32 GTR) 249.5 Kw

Top RB26DETT/RB30 modified turbos - Antonio (RB30 Powered R33 GTS-T) 319.5 Kw

Zoom Magazine Encouragement award - Wilch (R33 GTS-T Series 2)

Overall competitor summary:

R33 GTS-T

B-Man - 327.9 Kw

Antonio - 319.6 Kw

Jimbo - 215.1 Kw

Sparki_D - 215 Kw

R33vit - 197.6 Kw

Goldrays - 181.6 Kw

Scott - 180.2 Kw

Ash - 173.0 Kw

Wilch - 166.9 Kw

Neil - 159.8 Kw

Eden - 158.3 Kw

R32 GTS-T

Silver GTS-T - 150.6 Kw

Cereal_Killer - 137.8 Kw

GTR

CNG - 301.3 Kw

Dave - 283 Kw

GTR032 - 188.6 Kw

Misc Entries

Grant - Soarer - 263.2 Kw

Andrew - Supra Twin Turbo - 246.2 Kw

Stewart - E46 M3 - 183.9 Kw

Haroon - S13 Silvia - 158.6 Kw

Kel - 350z - 156.9 Kw

Kinks - R31/RB20DET - 144.5 Kw

Sean - Supra Non-Turbo - 111.4 Kw

Carlo - Supercharged MR2 - 87.2 Kw

Chris - Datsun 240z - 67 Kw

Duncan - Datsun 200B - 49.7 Kw

Thankyou to all of you who attended today for making it a truely great day for all!

dsc01335.jpg

dsc01330.jpg

dsc01352.jpg

dsc01349.jpg

dsc01353.jpg

dsc01371.jpg

dsc01378.jpg

  • Replies 74
  • Created
  • Last Reply

Top Posters In This Topic

good day

did 321 GO have a turn?

and whos posting up photos???????????????????????????????????????????

sure did. Andrew made 178rwkw if memory serves me correctly.

I'm really disappointed with my dismal dyno effort. I have no idea why it was so low. I made 131.7rwkw previous with just a 3" dump / front pipe. Now with a full 3" including high flow cat, front mount and pod filter I managed a shocking 137.8. Very confused. :(

congrats to BMan for the highest figure of the day.

Yep Andrew's 321GO RB20 R32 GTS-T made 178rwkw with E Boost set at 15psi standard RB25 turbo, FMIC and full 3 inch exh. Also Dave's GTR who won RB26 stock turbo went back on dyno last and sorted out boost controller and made 280 somethingrwkw. Yes it was a big day and thanks to SAU gang for the biggest ever Dyno Day we have had. Thanks Uncle Nick and Carlo. Lots of good pics including that immaculate purple GTR.

PS. I had my third V drink in my life. Hope I can sleep tonight. I think I might be dreamin Skylines.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...