Jump to content
SAU Community

Help: R32 GTR - why two different o2 sensors? Anyone used the EL Faclon in a GTR?


Recommended Posts

The R32 GTR has two different O2 sensors - eac has a different part code and price with Nissan. Anyone know why?

Since I have to replace both, I was wondering if anyone had used the EL Faclon universals?

Since the GTR is known to have a lean #6 piston, I'm worried that using the EL Falcon option might lean it out and blow engine up........ which would be very baaaad....

Would aprpecaite people'sexperience/knowledge in this area.....

The car won't lean out and blow up due to the O2 sensors, they are not refferenced under full load (WOT). They are there to enable the car to be fuel effecient at cruise (part throttle/light load) conditions. Can't advise you on using the universal sensor, but as long as it fits, and give the right volatage signals there shouldn't be a problem.

Richard

i would have a stab in the dark and say that one of the sensors may have a diffrent connector on it...this would be for front and for rear half of the engine...the reason behind this would be so that you dont connect them arse about....i would assume the actual sensor will be the same....just the connector would be diffrent....if not...just possibly a longer lead on it

i would have a stab in the dark and say that one of the sensors may have a diffrent connector on it...this would be for front and for rear half of the engine...the reason behind this would be so that you dont connect them arse about....i would assume the actual sensor will be the same....just the connector would be diffrent....if not...just possibly a longer lead on it

Could be the case. ONe is a three pin, the other with 4 pin (but only 3 pins used), but there's a $10 price difference between them. I thought perhaps Nissan might be clever and use two narrowbands to get a wideband reading.......

So, has anyone fitted the Falcon EL universals to a GTR with GOOD Results?????

if thats legit ^^ then id look into that xfixiate. el falcon ones are 70-120 ish each?

Universal EL Falcon $100 new each from Petrojet.

But since no-one can seems to know the mapping between them, then how dya know that the voltage going back from the EL isn't read by the GTR CPU as too rich and the mixture is leaned up?

Burn your valves out or blow a piston to save a couple of hundred bucks?

I'd use them if I could get the data, or be able to talk to someone that has dynoed the EL Falcon ones on an R32 GTR and looked at the results....

Matts would be 2nd hand? Since they are supposed to be replaced every 40kkm I think I'll be buying new ($400 for both)

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...